Search results

Anyone else have roaches in their laminar holes? If so how do you deal with it, I pulled one out today to try and clean it out and work on it and there was at least 3 roaches. Call me a baby but I don't like roaches. I pulled up the other one yesterday or the day before and there was a roach...

I have I guess like most people a drain and a skimmer with Jandy never lube valves that I can open and close to turn the skimmer/drain on and off. I noticed today some bubbles in the filter basket and my laminars were spitting so I"m guessing I have a little bit of a suction leak. What I...

I took out the filter to clean, put a different one in, and it won't stop leaking at the oring. The oring was deformed so I just bought a new one and its still leaking. Does anyone have any ideas?

I've asked before never figured it out so figured I would try again on here. I have an Aqualink PDA system with a Pentair Variable speed pool pump and Pentair Laminars, 2 of them. The problem I have is I turn on my laminars and they work great. For about 30 minutes or so. Then they start...

Hi, Noticed my pool on routine test was at close to 0 chlorine. its been raining alot so figured it might be that, but when I looked at my cell, there were hardly any bubbles showing. Its a aftermarket clear cell. link to cell below. I do see some bubbles coming out of the returns in the...

As subject says I have the Pentair Magicstream Laminar's. I have two of them. Both appear to be hitting the edges of the hole where they shoot through the top cover. I do not appear to see any real adjustment on the side knobs, is there some type of trick to this? And also am I suppose to...

Edit: Apparently the two options are sunseeker/pool tone and j&j. Sun seeker is significantly less so hoping someone got it to work with aqualink What are my options for replacement lights for jandy led Lights? These are standard niche lights. I replaced one about 5 years ago or so and now...

I asked about this a few months back I guess. One of my valve actuators randomly decides not to move it’s the one one that picks to pull from the pool or spa and caused my spa to drain. It switched fine to the spa but didn’t switch back. I played with the switch on the bottom and it didn’t move...

I typically use Liquid Chlorine from the pool store. 2.5 gallon jugs around here, I believe 10% concentration, but I hardly need it as I have a salt generator. However sometimes with very heavy rain, or when away on a trip and something goes wrong I need some chlorine. Its a pain to...

My aquapure has been fine, but now I'm having a weird problem. My old cell was dying I was pretty sure so I got a new cell. Before that though and to appease the wife before spending the money, I added some salt to the pool as the error for dead cell can also be because the salt is too low...

Moved from HERE Hi I know this is old but I need to tackle this soon. I have 3 jandy color lights all 3 are bad at some or all colors including one that I replaced about 3 or so years ago. Do these replacements work with jandy pda system?

Can someone tell me how to test. The pool/spa electronic valve all of a sudden moves when it wants or not at all. I assume the valve is good as it does move. What Is the best way to test?

So this is an ongoing problem now. I used the cheap flappers and they would work for a few days then might not, then work again, then I would put some lube on the flapper and it would work again maybe for a night or two. Now I broke down and bought a Jandy one and its leaking down as we speak...

Hi, Heatpump was working last year, Went to use it and the fan won't start up. The display appears to be long dead on the heat pump so I can't see anything. I don't see any errors on the PDA. Any ideas before I call someone? It was working less than a year ago.

Essentially a robot with a tethered battery that can also solar charge. Says it takes like 2 days in full sun to charge if you just use solar. I was looking at the Aiper cordless robot as I love my polaris robot but the cord is kind of a pain. The Wybot is currently cheaper than the Aiper and...

I bought a new flapper and spa still leaned down. I then greased the flapper a bit and the pool didn’t leak for 3 or 4 days. Them it leaked for about 4 days and I greased again yesterday and it didn’t leak last night. Am I supposed to grease the flapper and if so how long should it last?

Not sure if this is the right thread for this. My aqualink is controlling my aquapure just fine in pool mode, but in spa mode, it shows 00% even though it is set in the PDA.

Hello, I have two pentair laminar, why I have Pentair with a jandy system is beyond me, but anyway, I noticed yesterday that if I pull the laminar body up slightly so that that the plastic top piece is above the ground, the laminar works perfectly, but if I drop it back flat in the ground, its...

Was just using the unit probably last week. Went to turn it on again to get it out of the pool to empty the basket and the control unit does not function at all. I thought maybe it is the outlet, but the grill plugged into the same outlet is working fine. Anyone know if this common and if...

As subject says. Cable foam is starting to tear. What can I use to repair it? I used e6000 which appeared to work nicely but appears to be breaking down with the chlorine

I think this is the right place for this. I replaced the flapper valve which usually fixes the problem. I've done this a couple of times I guess since we moved in 7 years ago. This past time was about a year and I noticed the pool was bleeding down. I replaced and new one appears to be...

So somewhat related to my other post, before I go and replace one of my pool lights, how do I reset the Jandy lights to try to get them back in sync? One of them is out of sync. I read the instructions and it says shut them off, then turn them back on I think in 6 seconds or something, but how...

Hi, I think one of my lights is bad and looking to replace. I replaced the spa light before and bought a 120V replacement, but this was back in 2016 and I just replaced the light engine. I am pretty sure I would have confirmed when I did it back in 2016, but of course now I'm not sure. It...

https://photos.app.goo.gl/wJ8n8vpx9ZrtgZSG9 Hopefully you can see picture. At bottom you can see jacuzzi is starting to crack apart. Ideas on how to repair and especially how to do it aesthetically pleasing. I've seen concrete repair, but I don't know how nice it will look. Top of jacuzzi is...

No error codes. I just got this cell to replace old one that was throwing code 121. I checked cell voltage and it was 29.8 volts both ways. I did notice that center pin was sparking when I removed and replaced the cable. I don't remember that happening previously. No matter what I can't get...

So the top of this piece broke of. Any idea why it broke and more importantly how I get the rest out to replace?

As seem in other thread, my jandy cs200 has a leak. Are there any other filters that have the same plumbing with inlet and outlet so I don't have to repipe? I assume like most industries the jandy probably has 3 other companies that have a copy cat model

I thought I would write a quick review now that I have played with my new to me cleaner for a little bit. It is a little over 2 years old but did end up with the swivel cable that the current models have due to warranty replacement. I honestly see the swivel cable doing nothing, same as my...

Hello, Sadly my smartpool nc74s cleaner is being retired due to being discontinued and getting stuck on the main drain. I"m picking up a used Polaris 9550 which from all the reviews should have no problem with the main drains. I'm wondering from people that have had these Polaris cleaners for...

Hello, I have a smart pool scrubber nc74 cleaner. When I first got it. It would get off the drain in 30 seconds or so. Now it constantly is stuck, it works fine otherwise and I recently replaced the track and brushes and yet it still gets stuck. What is the best option to stop this? Its a...