Search results

Thank you for your help. I am going to close this out. Jandy does not offer guidance on locating a repair center. The people that I have contacted from the Jandy site seem to want to measure voltages like I did to confirm the cell is bad. at $85 per hour then a cell is $600. I am sure it is...

Yes, that is my plan. Thanks.

I'll try different people from the site then until I come up with someone who has service center capabilities. Thanks

I did call Jandy and they will not test anything themselves. They gave me a phone number of a local technician. It was mentioned that the technician would measure the voltages and decide if the cell was bad. I mentioned that I had already done that and that the voltage was high. The cell...

It turns out that my house borders Riverside County and my city does not care if I use salt. As recycling water becomes more accepted and necessary they will turn up the heat on salt in the sewer systems universally. Until then it does not matter in most areas. People in California think the...

I am getting mixed information about the systems being legal in my area. I just became aware of this potential problem last night and will find out Monday morning. I am in Riverside County in the state of California. It might be that the problem is with commercial units at this time. I'll...

Thanks. The outside post are in very good condition. I'll find a service center and have it checked out.

The Salt systems which remove the Calcium and Magnesium are not popular in my county any longer. Will a salt-free system reduce the hardness of my pool water if I swap some of the pool water out for salt free softened water? My understanding is this process only keeps the bad minerals materials...

That is a very good idea. I may have a receipt problem since I purchased the house but I'll figure that out when I get to that point. I have attached a picture of the cell. I believe that the electrode has etched away on the right side probe. All indications are to replace the cell if the...

That makes sense. I am in Palm Springs and the water is really bad. Very hard with a lot of Calcium. I'll look for a thread or start one regarding refilling the pool using soft water and my auto filler.

The temp is correct and the Salinity are correct 3.1 and 83F. The SWG It did not like the boost and the service light came on again. code 120. I turned it off then on and it is running correctly. I'll run it a few days at the normal settings (40%) and see what happens. Over the weekend...

You may have saved this SWG unit. The SWG has ran 15 minutes correctly with your changes. The cell shuts off and rests. I then up the percentage of time and the cell turns on. Turn the time down and it rests again without error. I am running it at boost right now for an hour. If it does not...

Yes the adapter board is still installed. The program is on A. I could not find the firmware type without removing the PC Board. The software code that came up on the LED did not appear in any documents so I left it on A. I assumed that it only affected the salt water reading, I'll make those...

The chord and salt sensor all appear to have been replaced with the new cell in late early 2019.

Hi James, The model Number is a Aqua Pure 700. The label says both Aqua Pure 700 and Aqua pure 1400. A dot exists next to each model number. The dot is marked in alignment with the Aqua pure 700 label. This is a Aqua Pure 700. Is that the model number that you are asking about?

Hello James, Sorry for the delay and thanks for the response. Here is a picture of the board. I have the system running and producing chlorine. It still stays in the reverse mode a long time and will generate the 120 or 121 low current error code. This will go away in a half-hour or after I...

The cell is the 700 with two leads.

Thank you for this information. I'll post a Leslie pool supply report. I have fixed a few items . Getting ready to fix a few more. I'll start another thread

New pool owner through a house purchase 3 months ago. SWG unit worked well.The cell was new 6 months ago. Cell exposed to 4500 ppm salt and high chlorine. Pool guy is gone now after cell quit and chlorine was low. Drained the pool and salt is at 3200ppm now. Cleaned the cell with Muratic and...