Search results

Everything since my calibration seems to be good. Now that the water has warmed up it seems a lot more stable than it was a few months ago.

I am about 90 minutes north of you in Wichita Falls. What CYA level do you shoot for. You seem to be a salt expert. No use of reinventing the wheel if you have knowledge

Yes I use tap water. I don’t know the level of the fill water but am assuming it’s low due to the fact it’s at 200 after replacing 80 percent of my water

Thanks is 300 on calcium high enough?

I have had a pool for 10 years and have been on an off the site. I never had good luck with my SWG because I was too cheap to run my pump the time it needed. So I switched to chlorine pucks and of course my CYA skyrocketed. Approx 1 week ago I drained 80% and refilled and did a slam to clear up...

or just replace the motor....cheaper and no plumbing involved.

You will want it on a timer. I run mine on the same timer as the pump that way one cant be on without the other

I will get a test kit coming....but I went to another local pool store and the gave me the same salt reading...within 100 ppm. So having 2 test that are close and am close to what I think it should be due to the amount of salt I added I went ahead and calibrated the cell based on what James...

i had been using pucks for a year and a half and cya was through the roof so I did and 80 percent drain and fill. So I am assuming low salt as we have good water. I added 400 lbs of salt and according to my new aquachek salt strips I am at 4000 ppm. The new cell and sensor says I am at 4700. I...

I added 400 lbs about a week ago. Guess I will see if the pool store will test and compare results to see which reading is off The pool had to be mostly drained to to cya issue so there should have been almost no residual salt.

Yes it is a brand new cell and sensor.

I got the aqua check strips based on what I saw here I thought they were good.

I don’t have the iaqualink only the old rs. After it dried out it’s working but getting error code 145 on my new salt cell. According to test strips I am at 3500 not the 4800 the cell shows

It is in auto mode. I have never seen lockout before and the panel buttons don’t work either. Update I was able to get the buttons to work randomly last night. It would turn on for 30 seconds then shut off. Gonna wait till the rain passes then troubleshoot some more.

My aqualink rs has been working fine. Today I got a new salt cell Jandy 1400. I replaced the cell and now my aqualink on my PDA says lock out and the hard buttons do not respond. I had to pull the flow board because mine was old but installed as the instructions with no board. FYI it did have a...

It’s a 3 port. Seems like I was replacing them about every 3 years and was still having to supplement chlorine. For me it’s cheaper to just add chlorine

I have an aquapure 1400 and after the cell went out several years ago I have went to chlorine. I would like to just take to old cell out and put a piece of pipe in. I am kind of ocd as I don't want to cut any pvc. I am looking for the threaded ends that will fit a jandy union. I really dont want...

This will be the 12th year of my pool and knock on wood I have never had to replace the pump or pump motor. I know that is a lucky streak. Now when its cold I can hear a little bearing noise so I know its a time bomb. I have on old aqua link with the pda. It used to be a salt pool but I got...

I am in north Texas the water temp was 52 and the salt was 2.5 going to bring it up today and see if that helps. The cell is exactly one year old and I'm going to clean it today and see if that helps. The cord should be the correct one as I saw him replace it this time last year. Sent from my...

That's what I here but I have had nothing but bad luck with them. Sent from my iPhone using Tapatalk

I've had my pool approximately five years and out of that five years I've replaced my cell three times but only once I've had to pay for it. It's a Jandy aqua pure 1400 and now it's back to throwing error code 120 and 121. It should be under warranty but in case it's not would you recommend...

Need Help with Equipment I have a Jandy rs system with the aquapure 1400. The salt cell has lasted approx. 3.5 years and during this time it has had to have 2 new sensors. The pool was under warranty so I did not care. Now that it is my turn to pay I did some research. From what I have found...

AquaPure 1400 Help I have a 4 year old aquapure 1400 that seems to have a problem every year but this is the first time it is out of warranty. I am getting codes 125 and 194. The sensor is clean. Would buying a new sensor and cell fix my problem. Any help would be great.

I have a Jandy Aquapure RS panel and with PDA. My dog decided to eat the remote. So my options are to buy another remote or get the iaqualink. The question I have is will the iaqualink allow me to program my pump timers. Also where to buy it and what do I need to make it work. Thanks

Re: Aquapure 1400 Also error 127

Aquapure 1400 I have had my pool for about 4 years and it seems like every year I get an error code and the pool company comes and replaces the sensor. I am getting error code 121 right now. I am guessing that is the sensor again. Is this normal, I am not thinking it is. If not what could be...

Thanks I started slam yesterday. Gonna go for a few days before I try the overnight test.