Search results

Noticed that my intelliph reservoir isn’t lowering much. Tested the outlet hose and it is pumping nicely. My guess is there is some clog in the acid injection fitting since not being in use during the offseason. Any tips to clean the unit out if there is a clog or blockage ? Otherwise...

Moved from HERE In a similar boat ... my CH from the City is 200-225PPM... What solutions have others used at the equipment pad to install a softner for the autofill... based on plumbing... wouldn't be able to install it elsewhere?

Background: So just about a year after having IntelliCenter with the built in intellichlor board and transformer.... .. Early last year the IntelliPH board connector went out like most do in that internal connector area (was replaced under warranty) all good Fast forward to now (8 months) later...

Curious if anyone has found the right size rubber o-ring that goes on the backside of the upper low voltage front panel to keep the screws from falling out when unscrewing.... My o-rings have split and trying to find replacements to not lose the screws...

Today while having a pool party went to fire up the trusted Mastertemp 400 only to notice that the heat didn't increase in the spa.... Checked out the heater and noticed an E05 error on the heater.... I have the newer 6 button so i could only look at the IntelliCenter panel which is wired RS485...

Well ... as always... performed filter cleaning for the season and the air bleeder screen cap has a tear... just like every other year so far almost... What replacement part does everyone advise as there is Pentair and aftermarkets.... ?

Does anyone have a O-ring size they have found that fits the Pentair Air relief valve - 98209800? Need to replace the o-ring on my Pentair 100 Quad Filter

Curious what others have done for pool parties where there is a phone charging station(s) for guest to charge their phones. Something like this a dedicated locations...

Curious what techniques everyone uses to transport acid & chlorine across deck to not stain from rouge drips when adding to pool. Is there preferred buckets that are used to transport back and forth with gal jug inside? Trying to find a sturdy bucket method of some sort to keep the gallon jug...

Curious what latest solutions everyone is using for their cartridge filter cleanings. Debating over building something custom or getting a solution like the cartridge cleaning stand to ease the back.

Is there a preferred 3/8" float valve that works without subtle hiss/fill never fully closing? Using a MP Industries autofill. Tried the Stetson Development Inc Pool Pond Spa Water Leveler PVC Auto Fill 3/8" Float Valve but after a couple months doesn't fully shut off even after multiple...

Just noticed while swimming yesterday a 1/2 gap on the upper inside corner of our skimmer.. pool was finished in late 2021. Any recommendations to fill this void just so water does get back there during heavy pool usage etc otherwise water is obviously below it?

First season for new pool and learning & tuning as we move along.... I am noticing our IC60 occasionally isn't happy with flow and puts the infamous red light.... I'm trying to determine what the optimal flow range is to not cut it too close but not have to run VSF full bore all day.... also...

Please post all your intelliPH board / connector fried pictures as I work with Pentair and local warranty / service provider to build a case... Note: Key Pentair Components in the mix...

For those using the newer MasterTemp 400 with a intellivalve wired to the bypass on the heater circuit board…. What setting do you have the intellivalve set to so there is always a little water flowing through the heater when the heater is no on? Curious what number those set at to allow little...

New pool built late last year and being using the IC60 and IntelliPH wired in series for a month .... noticed today while testing FC we were dropped below 3.. Went to check out IC60 cell... no lights on... checked out IntelliPH and screen is blank Checked Breaker and not tripped Turned relay...

Preparing to convert to salt this week... did a couple readings over the weekend at registered 800-1000 ppm before adding any salt. Curious where these salt readings could be coming from given our environment... I believe there is some salt in the liquid chlorine I just tested tap and we have...

Anyone else having issues with the handle on a new Waterway Renegade Skimmer where is doesn’t stay locked into the sides of the basket and falls out? Curious if this is a defective basket with handle or just a poor design. Curious if there is a better basket to replace it with or how to get...

Curious what ideas others have to protect our intelliPH in-line feeder insert from getting hit and snapped off. Now that pool is in use a couple balls have landed in the pool equipment area and I feared it hit the intelliPH in-line feeder Curious what cage / support system ideas anyone has ..

We recently used our baja umbrella sleeve for the first time with 1-1/2 umbrella post It fits perfect in top of sleeve and snug but down inside the bottom of the base there is play so the umbrella post doesn't sit up straight. Curious what solutions folks have come up with to stablize the base...

What are the latest deck boxes people are recommending that can last longer than a season ? Have tried various Suncast and Keter deck boxes for toy storage, noodles, etc but they all don't last.. Looking for input for a nice deck box that will last, keep things dry inside, won't warp in sun...

Looking for umbrella ideas in pool with fiberglass pole... don't want any rust

Any tips on trying to get a new IntelliPH to start pumping since sitting for a month+? I am testing out our IntelliPH for the second time since pool was built late 2021, water temps are coming up, and planning to convert to salt and use our IC60. When I first tried the IntelliPH with manual...

Does anyone have any referrals for a service that will reglaze a 50+foot water slide into a pool in Southern California?

I am trying to determine the best way to schedule my pump to adjust to different speeds without causing the it to go off (causing it to go into priming mode, and then to adjust to another speed). Wiring of panel and relays are designed based on @MyAZPool setup Original schedule (pump start...

Curious what type of pad light ideas others have used to light up equipment pad at night... looking for something low profile that is adjustable that can mount to wood or unistrut where all other electrical equipment is installed. Entertaining this marine led deck light

Curious if anyone has a tip on how to create a circuit group that would allow one to drain a raised connected spa into attached pool or more service mode by design? I can do it manually with putting intellivalves in service mode... close pool suction/open spa suction (valve 1) and close spa...

What are these? I recently noticed what looks like tiny specks of rust on our pool walls and in some spots our baja shelf and steps..... These tiny specks don't seem to exist in our raised attached spa walls, seats or steps Hydrazzo Mediterranean blue was installed ~4 months ago and just...

I have the intellicenter which can be complicated for family and friends... Curious what others have done to help make controlling spa and lights easy when family and friends are using the pool with an intellicenter setup? Was looking at adding something like the Pentair Quick Touch II Remote...

Curious what others do for best practices with their Maytronics robot cleaners Just dropped our Maytronics Active 60 in our pool for the first time and watched it clean for 2 hours using the Regular // 2.0 Hrs (Cleans the floor, walls, and waterline). Not bad, curious how it knows what it has...