Search results

Video of the issue Pump is a few years old. This morning it decided to stop running on high but works fine on low. I think it ran on high correctly for a bit when it started this morning because I heard the spillover this morning. If I try to switch from low to high it attempts to start but...

Mostly where the sun hits the pool walls the most. Is this normal? The pool store employee said I shouldn't get any if my water is balanced. My alkalinity is just on the edge of being high but I can't imagine this is the cause. CYA is in range but on the low side. FC is 5.5 (I boosted the...

Any Omnilogic experts here? I'm having an issue with an endless boot cycle I am not sure what is going on with my unit. (installed 9 years ago) We went away for the weekend. At some point the Omnilogic board stopped communicating with the network. Looked like a bad RJ45 cable based on my...

So I recently replaced my SWG (replaced with a factory Hayward T-Cell 15) and replaced my Hayward 5.5 year old old pool filter cartridges with Guardian versions: https://www.amazon.com/gp/aw/d/B00J7XTBD8?psc=1&ref=ppx_pop_mob_b_asin_title And now I am seeing this in my pool and spa. I think...

I just replaced my T-Cell 15 and Haywards Omnilogic is showing readings of my salt that are higher then an actual test of the water. Test shows 3300ppm Omnilogic shows average salt 4390 and instant salt of 3781. Do I need to calibrate this somehow? I cannot find any info on needing to do...

My touchscreen is useless, has been for 2 years. But now I need to use it and I guess it's so far off on calibration I cannot get to any menus. I see the replacement screen on this site, but no delivery into Sept? That makes no sense. I cannot seem to find it anywhere else so I thought I'd ask...

I can't seem to find an identical replacement and there are so many choices out there. Per this thread, I think my motor is shot: https://www.troublefreepool.com/threads/pool-pump-no-longer-runs-on-low-and-blows-the-circuit-breaker-when-set-to-high.185054/

Hello, I have a Hayward (Century) 2 speed pool pump and an OmniLogic system to run all the equipment. I was in the backyard a few days ago and the pump ( on high) just shut off mid cycle, tripped the breaker at my pool sub, and ALSO tripped the main breaker at the house that powers all the pool...

Hello, I am having a strange problem and I am hoping I can get some advice. pool is only 4 years okd. Pool equipment is running through Hayward OmniLogic and the pumps have their own 20amp breakers, one for each. Every morning the pool pump kicks on, I can hear the relay click. The filter...

I am hoping some heater experts can help me out here.. My H400fdn Hayward Heater will not turn on with the Omnilogic remote. This heater is less than 3 years old and was installed with my pool by certified professionals. If I take the heater out of bypass mode I can run it manually without...

Hello, Late last year we put in a new pool. Two weeks ago I went to clean the SWG for the first time. It wasn't very dirty but it had been 5 months since it was installed. So I cleaned it, put it back, everything is working great. This week I received two warnings from the Omnilogic system...

Hello, I am new to the forum and new to salt water pools. We have a new pool that has been completed for about 2 months now. I am having issues with it maintaining any chlorine levels and I am looking for advice on what to try next. Here is what I have been doing, and my equipment. Hayward...

Hello, I am new to owning a pool and I think mine may be leaking under ground some where. sad.gif The water level of my pool will drop 1" every night when the filter runs. If I do not run the filter the water level doesn't drop at all. The pool is over 25 years old and was re-plastered 12-16...