Search results

I have a Dolphin M500 which goes in the pool about every other day, is it still necessary to brush the walls and the floor? Pool is and has always been crystal clear.

I don't know, although the experts here have had little to say.

I have been using mine since June 10th and it has not missed a test yet. I originally thought the FC readings were low but I know believe the readings from my TF-100 kit were incorrect.

The base of the tips are not the same size so I can't do that.

I'm assuming the smaller tip on the new bottle would cause smaller drops therefore giving a higher not smaller reading.

Holydoc, The water was in a sealed container and to verify the results I used that same water with the old reagent and still came up with 7ppm.

If I compare the two tips, the tip on the new bottle looks considerably smaller than the old bottle.

My FC seemed high using the Taylor's drop test so I took a sample to a couple of pool stores to see what their test would show. My testing indicated 7ppm and both pool stores showed 5 ppm. I recently bought replacement reagents for the R-0870 and the R-0871 which were a couple of months over a...

I'm seeing a difference of between 1.5 and 2 ppm from my taylors test. WG always reading lower. Also the FC data posted on the web page is not exactly the same as on my phone. How do I get to the screen on my phone as shown above? I do not see that on my android phone, all I see is the last...

If it does not perform well, I will return it. Taking the daily test seems to be the very basics. I'm going to be gone for a couple of days but I will post when I get back.

Results from 1st test FC 5.5 using drops and waterguru reported 4.1, PH aprox 7.7 using drops and waterguru reported 7.7, temp was the same as reported by screenlogic.

Also getting a "Sensor unit not fully in water" error even though the unit is completely submerged.

Thank you!

Just installed one. How do I access the "webapp"?

Thanks for your help.

My TA is low (40) yet my PH is and has been consistantly 7.5 , how critical is it to adjust this and what is the best way?

Jim, I will look at the display however, after turning it off at approximately 6:30 this morning it came back on as scheduled at 8:00. I will monitor it and maybe it will never happen again. Steve

Jim, I thought about that however it was never shut off and if I look at the history I see a continuous line. Steve

I have a schedule set in ScreenLogic for my pump to run from 8:00 am to 8:00 pm every day. Last night for the first time since installation a little over a year ago the pump did not turn off at 8:00 and ran through the night. Any ideas?

Thank you.

I'm trying to find a place to purchase an extra zinc anode for my CMP 25810-xxx-050. I have contacted CMP but they tell me just to go to my local pool store. I have searched on the web and cannot find it, all I see is the complete unit. Anyone know where to purchase? Steve

I will do that.

I have ordered one that will be here next week, I will have an additional 1 year on the warranty from my credit card. I am hoping to only need to use it during pollen season and when the neighbors lawns get mowed. Thanks for all your help. Steve

Thank you.

Thank you for taking the time to reply, I will look at the link.

I am trying to find a skimmer for the top of our pool and came across Solar Breeze. Looks pretty pricey. We have problems with the neighbors mowing their lawns when the wind is blowing and the fine clippings ending up in the pool. Also, a lot of pollen in the spring. Are the filters fine enough...

FYI Spoke with Pentair customer service and they said the temperature test is not a feature of the Intellichlor. They were very helpful and will be sending a flow switch to me.

Thanks

One thing I noticed yesterday while removing the unit to check it, was that one of the pins in the connector was longer than the rest, does anyone know if that is supposed to be that way or maybe it has worked its way out and is not connected?

James, Thanks for your help, It's greatly appreciated. Steve