Search results

Thanks, I have it all working.

Jim, Well tomorrow has turned into later. I am now ready to wire. I would like to be able to cut the end off the wire from the transformer and hard-wire into the box. I have enclosed to photos of the box. If you could give me some guidance I would be grateful.

Jim, Thanks, I am good with the screenlogic setup just was not sure about the internal wiring. It will be a project for tomorrow. Thanks again. Steve

I have read through the manual however it is not obvious to me how to connect the 120 volt transformer for my Volt low voltage lights. Just want to be able to turn them on and off with Screen Logic.

Lot of wind last night which blew through my skimmer and sent the cover flying. Trying to avoid putting the screws in and out. Anyone come up with a quick-release method? I don't see anything on the internet.

Jim, Thanks

My DE filter manual does not mention anything about recommended flow rate for back-washing. Does anyone have information on this? Thanks in advance. Steve

Jim, Really appreciate your help. A couple of things, my Screenlogic shows a Spa and I don't have a spa and sometimes when the mornings are cool it indicates spa is running when actually the pool is running. Also, it looks like I cant just increase or decrease the pump speed with the Android...

I have installed the Screenlogic 2 Interface however the user manual seems a little lacking. I'm not sure of exactly what I can do with this. The PC program seems to have more flexibility than the Android app. For example it doesn't appear that I can change the pump output from the Android app...

Thanks for your patience.

And I thought I was confused before I asked the question. So, when should I check salt level with the Taylor kit and when do I add salt?

Purchased the recommended Taylor K-1766 salt test kit and did a test this morning with the following results: K-1766 4200 ppm, test strip 3190 ppm and pentair screenlogic 3200ppm. What did I do wrong?

Thanks for taking the time to reply Seeing it's a new build I am going to contact the builder. Hopefully he won't say "they all do that".

How much if any air is acceptable in the pump basket? Running at 28 GPM for 12 hrs. There always seems to be an air bubble which appears to increase over time.

Thank you very much for your help!

Latest test data FC: 5 CC: 0 CYA: 50 PH: 7.6 TA: 140 CH: 300 Salt: 3300 (taken from pentair software (does anyone know how accurate this is?)) I'm planning on bringing the PH closer to 7.4 and raising the CYA closer to 70. Any Suggestions?

Thank you!

No problem, spray deck and landscaping need to be done.

Thanks for taking the time to reply. The FC is from the TF100 test kit. Hopefully once I get things where they belong this will be easier to control.

Latest results: FC: 6.5 (looks very high, maybe because I've been running the pump for a long time while adding stuff and rot reducing the % the SWG is running (60%)?) CC: .5 CYA: 30 (added 2lbs of CYA and will add another 1lb) PH: 8.2 (not sure why this shot up, will add 1 qt of Muratic Acid...

Thanks again!

Current numbers using TF-100 FC 1.5 CC .5 CYA Less than 20 PH 7.5 TA 170 CH 325 Salt 2550 Water temp 57 Given this information, what would you recommend I should adjust next? I really appreciate everyone's help.

OK, I have the PH at 7.5. Should I retest other levels before changing anything else?

Thanks for responding so quickly. I had look at that page many times but at first it looked like it was only for an update. Thanks again. Steve

Just installed a Pentair Screenlogic 2 and can't seem to find the software. No disk came with the unit. Done some looking online but I don't see anything that resembles whats shown in the manual. I'm sure I'm missing something. Does anyone have the link for the Windows software?

OK, being new at this, I think to start with today I'm only going to address the PH issue with about a 3rd of the recommended amount then retest tomorrow and keep adding day by day until the PH is correct. I will dilute in a plastic bucket and distribute around the pool. Then address the other...

OK, based on the Poolmath calculator I am looking at: adding 86oz of Muratic Acid 31.45-20 Baume to reduce the PH adding I gallon liquid stabilizer to increase the CYA (where do I get this?) According to my Pentair Intellichlor manual salt level should be at 3600 ppm. Poolmath tells me to add...