Recent content by russrimm

  1. R

    Low TA, continually rising pH

    I’m using a keto-ai smart skimmer but my Taylor and Leslies read the same. To clarify, I didn’t get to test the alkalinity while the pH was >8. But my pH climbs daily and I add acid every other day roughly to keep my under 8. I probably need to test TA more often but I tend to test it when the...
  2. R

    Low TA, continually rising pH

    I used my Taylor kit and then had Leslies check it too.
  3. R

    Low TA, continually rising pH

    Hi all, 15k gallon non-salt water pool. My TA was low 4 weeks ago (30) so I added 16lbs of baking soda. The pH kept rising to 8+ super fast after that so I kept adding muriatic acid to bring it back down. Today I tested my TA again and it's only 47, so I added 4lbs baking soda. My pH is rising...
  4. R

    Umbrella

    This is the ones we always use, always seems like a fair price and lots of colors. https://amzn.to/3wgrQeo
  5. R

    Pentair 120 volt LED color light stopped working

    $800 seems high, I think I typically spend $500-$600 tops for the larger pool sized and a couple hundred less or so for the spa sized ones, unless they've hit a supply problem like everything else is lately...
  6. R

    Pentair EasyTouch clock setting issue

    Hi all, Before I went on vacation, my pentair easytouch wireless remote transceiver went out so I changed it out and it resolved the issue. While on vacation, we had some power outages. Now that I'm back, my clock is permanently set to 12:00 in the year 2000. When I try to set the clock via...
  7. R

    Pentair - EC-522104 - Interface for Mobile Devices

    Hmm, maybe that's what's inside the box that's inside the box. I'll have to go thru the steps and see what I end up with. So now that I have this, is it silly to also still continue using the wireless remote as well? If so, maybe I didn't need to replace my wireless remote PCB after all.
  8. R

    Pentair - EC-522104 - Interface for Mobile Devices

    Hi all, I'm a little confused by the EC-522104 that I just bought and received. It shows on the diagram that it needs a CAT 5 running from it to my wireless router. If so, that means I need to run a CAT5 from my easytouch panel to a network jack which isn't going to be fun. When I ordered it...
  9. R

    Pentair Easytouch remote not working

    Very interesting - when only the pump is connected, it works! What does that mean? I ordered a new pcb for my wireless remote and a wireless kit to add. Is the likely bad wireless pcb likely causing other issues?
  10. R

    Pentair Easytouch remote not working

    I’m confused now because where it says Filter Pump under the filter pump and auxiliary relays (J8) there’s nothing plugged in. And it was working fine a week or two ago. I’m trying to figure out which of the three going to J20 is the pump, tracing them is hard with conduit :(.
  11. R

    Pentair Easytouch remote not working

    Boo It just went back to NO COMM on the pump status after the reset seemed to briefly fix it.
  12. R

    Pentair Easytouch remote not working

    I just did a reset and it says status normal now and the pump just kicked on.
  13. R

    Pentair Easytouch remote not working

    Sorry i’m confusing things. At the easy touch it says Status: NO COMM! The pump says running schedule 0 rpm and if I hit speed 2 or 3 it speeds up. So not only does my remote not work, the pump status is also saying No Comm on the easy touch.
  14. R

    Pentair Easytouch remote not working

    Merged threads. TFP Mod Hi all, I'm going out of the country for a couple weeks in a few days and freaking out a bit because my Easy Touch programming is wonky. I ordered the wireless kit but it won't be installed in time, and my remote quit working the other day, so I'm going to have to...
  15. R

    Pentair Easytouch remote not working

    Merged threads - TFP Mod Hi all, I've somehow managed to get my EasyTouch programming all messed up while troubleshooting my wireless transceiver board (which I have on order as there's no LED lights on it even though it's getting 15V). First question: I dont have the ScreenLogic2 so I can't...