I have Hayward equipment and my system reports zero salt. I assume my salt producer has failed. I googled the above and it’s out of stock in most places so I was thinking maybe there is a better or newer version for a 40k pool?
Replacement for Hayward turbo cell glx 15 w
- Thread starter dhodson
- Start date
- May 3, 2014
- 62,719
- Pool Size
- 6000
- Surface
- Fiberglass
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-40
- Jul 21, 2013
- 65,439
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
Low salt readings on a Hayward cell may indicate cell failure. Zero salt reading is usually a board failure.
This is the basic information we need to know in diagnosing a problem:
www.troublefreepool.com
This is the basic information we need to know in diagnosing a problem:
- Report all readings when you..
- Move the switch from auto to off and check all of the readings.
- Move the switch back to auto and recheck the readings.
- Move the switch to off for a minute and then back to auto and recheck the readings.
- What are the first seven characters of the cell and box serial numbers?
- What is the actual salinity and how are you measuring it?
Hayward Aquarite SWG - Further Reading
www.troublefreepool.com
Sorry for the delay and thank you. I purchased one of those electronic salt meters and indeed it is not low.
It says salt level 00000
All the other readings like temperature and chlorinate setting which is 80% seem correct.
I have glx-cell-15-w
Serial is 1E17118-401627
The motherboard was replaced about 18 months ago.
It says salt level 00000
All the other readings like temperature and chlorinate setting which is 80% seem correct.
I have glx-cell-15-w
Serial is 1E17118-401627
The motherboard was replaced about 18 months ago.
The salt reading is 4100
Unfortunately I was an idiot and when I saw the initial low salt error message the first time I put several bags of salt in. I plan to bring it down by filling the pool with additional water over the next month. There is an over flow.
The meter is easeasongear salt 3050
I’m not familiar with k-1766
Unfortunately I was an idiot and when I saw the initial low salt error message the first time I put several bags of salt in. I plan to bring it down by filling the pool with additional water over the next month. There is an over flow.
The meter is easeasongear salt 3050
I’m not familiar with k-1766
- Jul 21, 2013
- 65,439
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
Rather then making us guess what equipment you have please create your signature with details of your pool and equipment so that we can give you the proper advice.
This what I believe I have. Let me know if I didn’t include any relevant details
24' x 50' 40,000 gal concrete, Pro Logic is PL-PS-8-X288, Hayward Swim Clear Filter 550 sq feet, Hayward 2.5 HP speed pump and motor,Goldline salt system, 400K BTU Smart Therm (hayward) heater, Hayward booster pump model 6060, Hayward GVA-24 valve actuators, Hayward turbo Cell
24' x 50' 40,000 gal concrete, Pro Logic is PL-PS-8-X288, Hayward Swim Clear Filter 550 sq feet, Hayward 2.5 HP speed pump and motor,Goldline salt system, 400K BTU Smart Therm (hayward) heater, Hayward booster pump model 6060, Hayward GVA-24 valve actuators, Hayward turbo Cell
To be clear about the above video…
Should I obtain the chemical detector Instead of the electronic one I purchased?
Should I then attempt to set the salt level to that within the diagnostic menu?
Should I obtain the chemical detector Instead of the electronic one I purchased?
Should I then attempt to set the salt level to that within the diagnostic menu?
- Jul 21, 2013
- 65,439
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
What are the readings from the diagnostic menu?
I would get a K-1766 in addition to the meter.
I would get a K-1766 in addition to the meter.
