Search results

anyone know how to set a schedule to run my pump @ 1. Start 8:00 - 8:59 AM @ 3000 RPM 2. 9:00 AM - 4:00 PM @ 2000RPM' The problem it will not run in the Schedule, but i can hit the Pump Button and it runs at the correct speed for that time.. Zodiac is not much help...

It seams I am always chasing my PH & Alkalinity, is this do to my Salt Generator? Thanks

I want to replace my covers with a more flatter cover, my pool has 2 on the bottom of main pool and 2 on attached spa, i removed the one from spa to look for manufacturing numbers, the drain from spay had SP 1048E, do you think the covers in the pool section would be the same? I didn't want to...

I am replacing my old heat pump, and hooking up my Iaqualink to it. Here is where the old Iaqualink was connected. would i just hook the new heat pump in the same location, the round device with blue wire is that the temp switch? Thank you

is this still working I keep getting network error..

how to remove 3 pin connector to shorten wire on actuator.

I live in Florida, so do I need to have my vent install to drain down the panels, I think if the water stayed in them it would be better on windy days to have them heavier..There's really no freezing problem..

Should I put rubber strips under panels when installing on cement tile roof, to stop wear, from panel expansion ? Thanks

I have a leak under the panel which can't be seen from top, is the only way to fix this, to flip panel over? Thanks

what's the best way to remove it, to replace them? Thanks

Does anyone know where I can locate bearings for this motor, it's a Century motor. Thanks

I just replaced one that kept getting water in it, it's mounted vertical to control my solar system, any ideas how water is getting in? If it happens again I'll test the water to see if it's pool or rain water...

what needs to be done after a hurricane to my pool which was in great condition, no electricity now, should I dump chlorine in, since my swg is not running...Thanks

I keep fixing this, what could be causing this? I was thinking maybe water leaking in there, then the summer heat causing it to push up. What to use to fix this, I have been using hydraulic cement..Thanks

Anyone know an easier way to force this into the pipe? Sent from my SM-G930V using Tapatalk

I was installing some tiles on my waterline, and dropped some grout or thin set in the bottom of the pool, which hardened and when I hit with my brush I see a dark spot like the plaster came off and the gunnite is showing. Its about the size of a nickel... what to use to fix it, maybe EZ Patch...

I have some rough plaster on my tanning bed, I am going to drain it down to below the ledge for tile install. Is there anything to smooth out the rough plaster? Thanks Sent from my SM-G900P using Tapatalk

any ides on how to replace these tiles that we're loose, I took them off. I didn't see any water behind the tiles. Sent from my SM-G900P using Tapatalk

I am thinking of switching from autopilot to Aquapure 35, I have the IAqualink system. I am thinking this would be more compatible, automation wise.. Any thoughts on this? thanks Sent from my SM-G900P using Tapatalk

I switched Internet providers so I had to change the settings for the new router, I messed it up, now the drive in it isn't recognized, I I first hooked it up to the laptop out by the antenna, It recognized it, iaqualink showed up, I went through the setup, but when it asked me fo the ssid, it...

test results.. FC 7.5 cc 0.0 ph 7.6 TA 75 cya 80 ch 350 the only thing I did was add dry stabilizer to raise from 60 to 80...i can see the drain cover screws in the deep end, it just lost the shine. Could it be the stabilizer? Than You

I brought a sample to test for metals, it was iron .01. They told me my FC was 5 ppm, but i tested it just before going there and i got 11 ppm, came home and tested again it was 11 ppm, are there any signs of chemicals going bad, they 1 year old, store inside air conditioner home in tge dark...

Fc 4 Ph 7.6 Cc 0 Ta 75 Cya 80 Salt 3300 Water Temp 81 Yesterday it was at 8ppm of fc, i brought this up with liquid chlorine from 2.5. There are no signs of algae, water is clear. I talked to Autopilot about the swg, he told me to test it by capping the bottom then fill with pool water, and...

I have a total of 4 actuators setup, return, suction, solar, and cleaner. Is it possible to add more to the system? I want to add one more to open a valve for draing water. The plug for the jva have 3 pin, i do have the aux which are 2 pin connectors. Thank you Sent from my SM-T237P using Tapatalk

If the actuator is mounted vertical, can water enter through the back where it mounts to valve, and into the actuator?

I have an X Vac cleaner, looking for a swivel for the suction port if they make one, anyone know of one? Thanks

Any recommendations on a led bulb for pool & spa 12 volt white...Thanks

Well finished installing 7 Fafco 4 x 10 solar panels, I picked up 11 of them for 50.00. Then decided to paint the house..Thanks to the supporters of this site...

Do you have to drill a hole in the 3 port diverter valve so the panels drain down to pool? I have been reading everthing i could find, and that came up, it said Compol solar valve has it already, but i want to use a Janfy... Thank you

Does this cartridge have a top & bottom, is the top diam smaller than the bottom?