Silly Question about RJ-45+

[BabsNMK]

When picking the cell type in the control panel, is this considered an RJ-45 or RJ+45.

I had it set to RJ+45 and am getting lo salt/cell maintenance lights after running for a few. I just swapped to RJ-45 and it seems to also be running, no lo salt as of yet, but the unit reads about 900ppm less than my manual test.

Before I send it back to Circupool I’m hoping to find it’s a quick fix.

 

[PoolStored]

What control panel?

 

[BabsNMK]

What control panel?

the circupool control module where in the menu you can switch the unit type. Meaning I can select RJ-60 or RJ+60 or RJ-45 or RJ+45.

 

[PoolStored]

What cell did you purchase?

 

[BabsNMK]

What cell did you purchase?

RJ-45+

 

[PoolStored]

Post a picture of the entire controller and that screen.

 

[BabsNMK]

Post a picture of the entire controller and that screen.

 

[PoolStored]

The cell maint light is supposed to come on if the wrong cell is installed. Setting for you is RJ-45

 

[BabsNMK]

The cell maint light is supposed to come on if the wrong cell is installed. Setting for you is RJ-45

Ok so this is definitely an RJ-45? VS RJ+45? I wasn’t getting the cell maintenance light at first, I was getting lo salt and the wrong salinity rating when it was on RJ+45. For now switching to RJ-45 worked but salinity is still pretty far off.

 

[PoolStored]

For now switching to RJ-45 worked but salinity is still pretty far off.

That can happen, mine off 400. Call Circupool if concerned I have 60+ and mine is set RJ-60.

 

[BabsNMK]

That can happen, mine off 400. Call Circupool if concerned I have 60+ and mine is set RJ-60.

Great thanks!

 

[Texas Splash]

Ha ha. That's interesting. Now I have to go out and see what mine says.

 

[Rancho Cost-a-Lotta]

Mine shows RJ+45

 

[PoolStored]

Circupool RJ-60+ PCB Adapter Fixes "Cell Not Match"

I was a slow/late convert to SWG. Wish I had done it sooner now! In year #6, out of the blue, my Circupool RJ-60+ gave the "Cell Not Match" error. Prior to that, the only issue had been that the buttons on the control board became stubborn. When the cell error message came up, none of the...

www.troublefreepool.com

 

[Rancho Cost-a-Lotta]

I found this on the support page:



Check the tag on your cell...

 

[PoolStored]

I found this on the support page:

See the post above, OP should contact Circupool about the PCB adapter when you get the cell mismatch issue...

 

[Rancho Cost-a-Lotta]

See the post above, OP should contact Circupool about the PCB adapter when you get the cell mismatch issue...

I see. Thanks.

 

[BabsNMK]

See the post above, OP should contact Circupool about the PCB adapter when you get the cell mismatch issue...

So I actually don’t get a cell mismatch error. It was just that I was getting a lo-salt reading. I switched the setting and it was fine until tonight and now I get a hi-salt reading. I was trying to avoid sending it back to them but it looks like I may have to.

 

[BabsNMK]

Also, my cell doesn’t say positive or negative like that. In my email the sales receipt says RJ-45 plus but this is the cell.

 

[Rancho Cost-a-Lotta]

See the link here...High Temp Error. CP will prorate the new flow switch if still under warranty

Circupool SWG - Further Reading

www.troublefreepool.com