Filter Gauge On/Off Readings
- Thread starter dielseman
- Start date
Why do I need to use boost mode? I am adding liquid pool chlorine manually.
Boost Press and hold the POOL TEMP -BOOST- button D for 10 seconds to enter the Boost mode (Note ‘bo’ will flash intermittently).
Boost can be used to set chlorine production to maximum (100%) for 24 hours of operation.
After 24 hours of chlorinator run time, chlorine production will return to previous setting.
To clear the Boost mode, press and hold the POOL TEMP -BOOST- button D again for 10 seconds.
Boost can be used to set chlorine production to maximum (100%) for 24 hours of operation.
After 24 hours of chlorinator run time, chlorine production will return to previous setting.
To clear the Boost mode, press and hold the POOL TEMP -BOOST- button D again for 10 seconds.
So, the Lo only applies to the temperature and not to Flow.
It says Flow because the flow is good.
If the Flow LED is green, then the flow is good.
Okay. I should still do this even though I am adding liquid chlorine? Should I turn off my SWG though iAqualink? It is currently set to 30%.
Does the gauge kicking down from 5-10 on the filter cartridge not matter? The flo light is green.
If the display says "Flow" and the Flow LED is green, then you have enough flow.
Turn off chlorine production until the water is at 60 degrees.
The gauge can show zero pressure with lower flow rates, but you still have flow, which you can verify by looking in the skimmer and feeling the returns.
Turn off chlorine production until the water is at 60 degrees.
The gauge can show zero pressure with lower flow rates, but you still have flow, which you can verify by looking in the skimmer and feeling the returns.
I am confirming I turned off SWG from 30% to 0%. Another post of yours said 10%-20%. Yes, there is action in the skimmer and debris is getting into the pump. When do you typically recommend setting the SWG to 0%? The pool temperature has been below 55' for a few weeks.
Thanks for the help! I've turned it to 0% and will let you know.
TFP is a registered 501(c)3 non-profit that is maintained by user donations.
All of our content is free of advertisements.
Please consider donating at:
www.troublefreepool.com
All of our content is free of advertisements.
Please consider donating at:
Become a TFP Supporter
Help Support TFP Trouble Free Pool is run by a dedicated group of volunteers that … Read more…
www.troublefreepool.com
Hi all, I increased pump RPMs to 2250 and the filter gauge still has 0 as the psi. The control panel says 30% flow. What should I do to get the filter psi on? I am also having some issues priming the pump.
- Jul 21, 2013
- 65,095
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
Do you get a PSI if you n crease the pump speed to 80%?
Do you have good flow out if the returns?
Do you have good flow out if the returns?
Flow led button is green and skimmer does get debris and can become full if not cleaned. When I put the RPMs at 80% or higher there is PSI readings of 10.
- Jul 21, 2013
- 65,095
- Pool Size
- 35000
- Surface
- Plaster
- Chlorine
- Salt Water Generator
- SWG Type
- Pentair Intellichlor IC-60
Does your PSI gauge read 0 when the pump is off?
I think you are fine if PSI reads at higher pump speeds. With a big filter and lower speeds PSI is too low to show on the gauge.
I think you are fine if PSI reads at higher pump speeds. With a big filter and lower speeds PSI is too low to show on the gauge.