Search results

By control panel you mean the one outside? how do i select the proper pump in the iAqualink.

The filter pump, i can program any other button/device on the control panel but when i push the filter pump button nothing happens.

I finally got around to installing a new light i went with the sr smith treo micro led light as recommended by santacruzpool. It is only a 2 watt light but just the right amount for my spa.

I have to press the filter pump button on my rs6 to turn it on and off manually. When i am in the programming mode and it asks me to select a device to program i press the filter pump button and nothing happens. If i press any other button/device to program it proceeds to the next step in the...

I got the new transformer, i decided to test the old one one last time and it turns out i was testing it wrong. I put one test lead onto one of the two output wires on the transformer and one to a ground in the junction box and it was showing 6.5 volts that way, however when i hooked up the...

Thanks, ill update after the new transformer.

Well, theres good news and bad news. The light install itself went smooth i tied the end of the cord of the new one to the beginning of the old one and pulled it through, wired it in exactly the same way as the old one. I go to turn it on and nothing. There is a transformer that both the pool...

I was able to find the same model from a1poolparts.com (jluw10-50) i think its a slightly updated design though the led board/bulb thing looks a bit different then mine. I hope i can handle the installation, thanks for the help guys ill post a pic when im done.

Yes, thanks Bama Rambler it looks like mine is model number jluw10 or jluw15 (both the same just different wattage) but it seems they dont make those anymore and there is an updated design now (jluw9w50 for example) can i still find my model anywhere for a direct replacement or will these newer...

I couldn't find any information about the hot tub anywhere, here are some pics.

Not sure, where would i look for that.

I just moved into a new home and notice the hot tub light is burned out. I drained the water and tried to replace it but just could not figure out how. It seems the bulb/housing assembly are all one unit and there are no brand name/markings on it. i can only pull it out of the wall a few inches...

The 3 jandys are new and the check valve below is new

yea that's what I thought and then I replaced the check valve for the spa pipe and installed new diverter valves as well. still does it. Can there possibly be another check valve in the piping under the ground?

With a bit of luck and ingenuity I was able to get some good results. I drilled out the rest of the broken stud and threaded in a similar size sheet metal screw and it went in nice and tight. Everything seems to be working great so far with no leaks. That noise of rocks bouncing around in the...

OK, well I have good news and bad news. Good news is I found the problem it was the thermostat the body of the thermostat had punctured and the wax material came out. I verified by putting it in a pot of water on the stove and the thermostat never opened. The bypass valve was still ok but I...

Yes, when I shut the pump off the heater shuts off with it and those noises I was talking about only last a few seconds. I went out and looked over the heater again. There is in fact only one temperature high limit sensor on the front header. I think i was previously confused by the parts...

It looks like the second one will be #17 on this parts illustration Hayward H-Series Heater - (ED1 Style) Replacement Part Schematic It looks like its either on the top or bottom of the header assembly from the heat exchanger i will look for it tomorrow and jump it as well and see if anything...

Success, I replaced the ignitor assembly and it works again. I noticed the new assembly has an updated design, The metal frame of the ignitor has a half-circle section that kind of wraps around one of the heat tubes for more stability or something. The original one didn't have that. Anyway...

Thanks, I took out the heater element today to get to the igniter and in the process the wire fell right out of the igniter it was pretty corroded. I just ordered a new one (part # haxign1931) hopefully that will fix it. I was just wondering how does the igniter also act as a flame sensor I only...

I have an older Hayward H400ED1 heater it just recently started acting up. When I switch it on you can hear the electric igniter for a few seconds and then the flame fires up. About 3-5 seconds later the flame cuts off. There is a "system normal" and "heating" light the system normal light stays...

Im not sure how to isolate the hot tub, Here are some pics of my setup. I think the hot tub water drops down to a few inches higher then the the part where you sit. (I haven't had the pump off long enough to see how far down it goes yet ill try to do that and see) (The hot tub light is the...