Search results

Without the ability to inspect, what do you think is the problem with this pool? cost of fixing?

So i am having issues with the ORP sensor in my sense and dispense system. The OPR doesn't make sense sometimes it is showing 600 when the fc is 12 and 630 when the fc is 3. So i contacted Hayward support, they asked me for the pool test result which i gave them CYA = 70 pH = 7.5 TA = 110 CH...

I have the rainbow 320 installed (new pool) i want to replace it with a Stenner 45MHP10. Can i use the injection input already in use with the rainbow 320 with the Stenner? or do i need to redo it? I have an Ecommand 4 with a VS pump, how to i connect the Stenner to the Ecommand 4 for power...

When is the best time of the year to purchase a SWG system? is it in the beginning of the session at the end?

What do you think about this? Free Pool Heater - YouTube

Hi All, ~2 years ago i built my own above ground pool in previous home, and you were a big help Newbie - need some help A year ago we moved to a different home and now we are ready to pull the trigger for an IG gunite pool. We don't have much room in our back yard so we try to maximize the...

OK so it's been decided to get a new home with a pool (IG) All the places I've seen so far are with IG concrete pools. What do i need to check about the pool to estimate if the pool is in good condition or not. I heard it can cost 30-50K$ to fix a problematic pool in our area so that is a...

Weird question i know, but i got a new Hayward pump and screwed in the PVC fitting using teflon tape, i didn't use PVC glue on that part because it needs to be disconnected in the future. it always leaks no matter how hard i tightened it and how much teflon tape i use. Should i put PVC glue...

My CH is 50. I have an intex pool and i read that you don't need to deal with CH on an intex pool But what about my heater and SWG? their manual say i need CH to be between 200-400. What should i do?

What is the best way to use a gas heater? with the pump on high or low? I have 1HP 2 speed pump with a hayward heater (100K), when the pump is on low the heater will not turn on unless i put the pump on high and set it back to low, also in the low position the heater pump very hot water into...

Sometimes when i have more than a handful of people in the pool it can get dirty really fast. Can i run the pump (on low) when people are there?

8 weeks ago , purchased a new SWG system from intex. 4 weeks later the pump started to make grinding noises, i called Intex and they sent a replacement. Yesterday while the unit was running, after a min or two the service light went on and the pump shut itself off, i called Intex and they said...

To make a long tory short i am looking to replace the Intex pump with a pump that can connect to a timer (which the Intex can not) and would be low noise. How can i find the mount of noise each pump makes? i can't seem to find it in any of the spec pages i've checked. Can someone recommend a...

Did my first test today: (SWG) CYA:60 PH-7.4 FC-8 CC-1 TA:125 CH:100 What should i do? just follow poolmath?

Which one should i go with? http://www.amazon.com/Hayward-SP1091LX-Dyna-Skim-Above-Ground-Accessory/dp/B002DPY196 http://www.amazon.com/Hayward-SP1091WM-Dyna-Skim-Above-Ground-Skimmer/dp/B002KMIK26

What will you recommend for the Intex 18x9x52 ? Will the Aquabot Jr. do the job well or should i get something else?

i would like to buy a saltwater system to my pool (intex 18x9x52) i am thinking on the INTEX 2650 My question is, how far can i install it away from my pool? is 10-15' would be ok?

Hi All, I am new, but i read a lot here and getting smarter by the minute. Thanks you! I do have a question about how to level my yard. I bought an Intex 18X9X52, i am wondering if i can level the ground by putting cement/pavement blocks on top of it? the ground is already close to being...