Search results

Thanks for starting this thread @Jimrahbe . My Active 20 just died after 7 years and no amount of troubleshooting could get it to work again, so I decided to take the plunge on an EVO 614iq. Marina had it shipped to me in a couple days. I am thrilled with how nicely it cleans. My Active was...

Thanks very much for the reply - appreciated!

I've seen a few other forum members here complaining about the same over the years. My 2012 pool construction included SAVI Melody LED lights, and per some of the install documentation I saved, they reside in a 1.5 inch threaded housing, then cable runs through a very long conduit run to a 12V...

This is awesome! Thank you so much for taking the time to point me in the right direction. I really appreciate it

Thanks. I'll look into the capacitor angle. So far, no codes, and the service light is not on either. I need to do some searching to see if Pentair repair/service tech manuals are somewhere on the web too, beyond just the owner's manual I have on hand.

Fan runs. It does the normal start delay for 5 minutes, then I can hear the compressor humming or slightly buzzing for just a short bit, then nothing, then it tries again moments later. Would the compressor overall be the most likely failure if we had a water flow failure to the unit? I'm...

I checked the wiring after removing the exterior and electrical panels. Everything looks brand new - no visible issues of melting, etc.

Thanks - will do! When they have melted like that, the unit still tries to run? In any case, were you just able to strip and reconnect or was there an underlying issue that caused the wire to melt which also needs attention?

Found another person's youtube clip. This is what mine sounded like when we started it back up the first time after the auto shutdown from losing water flow.

We lost flow to the heat pump while it was running. It of course sensed this and shut down automatically. We've never lost flow to it before, so this is a first. We restarted the heat pump, and when the compressor kicked in after the usual 5 minute startup countdown, it was much louder than...

I think you were correct. It stopped chirping after a few days. No noise issues after stopping and starting up a couple times too. Perhaps it was just the new seal. I am relieved (for now anyway - ha)

Yeah. I don't regret trying to fix it. In any case, I learned how everything comes apart and can easily deal with a motor replacement now if needed. I'm keeping an eye on it. I shut the pump down last night. When I turned it back on, I heard just a short chirp vs sustained, and now it sounds...

Update. I must not have caught the situation quickly enough. The motor is starting to make a constant cricket type chirp today, so I’m assuming it’s bearing trouble. I may just have to order the new motor after all.

I reassembled everything yesterday with the new plate and seals. The only thing I had to rig a bit were a couple bolts which I could not source same length locally, so I just stacked stainless washers on them to ensure they did not go too far into the plate's receptacles. I decided to wait...

Yeah I know to do that now. The replacement seals I ordered are Pentair OEM, so hopefully good. I will definitely inspect the pad for any future leaks a lot more closely!

Here is the motor just before painting - note the corrosion that led to so much metal basically disappearing on one of the bolt holes. Given my experience with this issue, I think it's fair to say that if one has an intelliflo it makes a lot of sense to partially disassemble every 1-2 years and...

I’ll try to post some pics later, but wow one of the lower corners of the motor housing is corroded to the point of missing substantial metal material. Fortunately, the bolt hole is still there and appears to be beefy enough. This is the lower part of the motor one of my seals must have failed...

Thanks. I just ordered the plate and new seals. Pentair 071734S, and the housing gasket and diffuser gasket. All genuine Pentair. Friday delivery. Weather permitting, I'll clean the rest of the flaking enamel off and lightly sand the corrosion, then mask and hit it with rustoleum spray...

Thanks both. It's coming up on 7 years of service. Here are some pics of the motor and some associated parts. Apologies for the quality given had to use a flash with parts outside and dark here now.

I started having a buzzing or vibration type noise over the weekend. Not high pitched. I disassembled the motor tonight expecting to find debris in the impeller but nothing. Then, when getting to the last step with the four bolts on the almond seal plate, after loosening the two upper bolts...

Here's what I have to work with after getting the tape out tonight: The useable roof area on top of the pergola is 12 ft 7 in deep by 25 ft wide. There is about a 5 inch difference in roof height from house to edge so the pitch is at least there. A couple questions I need to research, so if...

Jblizzle you and I were thinking alike/typing at the same time. Sorry for the duplicate info

Thanks. It is a well built structure. I may add a couple more large anchors to the house ledger board just to be extra conservative, but it is probably fine as-is. According to one of the manuals I have seen online (fafco), a 4X12 panel filled with water weighs just under 70 lbs. Even if I...

Just ruled out heliocol. Can't seem to buy them without a local dealer/installer in this area. Looking at online sites for other options!