Search results

Thank you very much. So if you are on deck jet and bubbler and go back to deckjet only do you just turn off the combo button before you switch over? So I guess is what I am getting at is do you just make sure you shut off what you were previously using before going to the next? Also do you...

Yes I was hoping it was smarter or at least let me add the option in the feature circuit to shut one off when the other is selected.

Hello I have an intellicenter controlling a dedicated intelliflo pump for my laminars and bubblers. I have Valve A turning on and off flow to bubblers and Valve B Tuning on and off flow to laminars. I have having trouble programming this is the intellicenter Circuit Groups. I tried creating...

Thank you!!

So the b est way would be to just change the swg and heater wiring to 240v and run them both to the load side of the filter/pump relay then wire the 240 breaker and Pentair intelliflo to the line side?

One more question. I got the Pentair breakers. Does the neutral wire from the swg go to the breaker directly (running transformer in 120v) and the pigtail go to the bus bar. But it looks like they have the heater connected to the 2nd half of the load side on the same relay. So for the main pump...

Thanks again for everything. I have the pump and will connect it up. I also ordered the Pentair gfci breakers for each pump. Again I really appreciate it.

I was wondering about that. we didnt do the installation on those and the pool service guy said that most pumps are not on a GFCI. Should I change all of those breakers out for GFCI and if so I think I read in one of Jims post to use Pentair ones is that correct? Will that affect my IC40? I...

This is fantastic thank you so much!!! I really appreciate it.

The blower is polaris 1-480-02 but now I see it does 5.8amp. The main pump usually runs about 2200 rpm and the features pump we have not put in but it will be running 2 laminars (10gpm each) 2 bubblers 50gpm each) but I would not think I would be running them that high.

Thank you so much I will add it to there. Just out of curiosity with the blower rated at ~12 amp and the pump at 11.8 amps will I be popping the breaker or does the pump run at much lower then it’s max? Also with 50 amp total at the panel will it still be ok with the 3 pumps, heather...

I mixed that up the top 20 amp is the intelliflo. Middle is 15 amp is the whisper flo pump for spa jets bottom is 20amp blower (pic attached).

Thank you for the info. The top 20amp has a Pentair intelliflo vsf (pic attached) and an ic40. The lower 20amp breaker has the Purex triton whisperflo (picture attached) for the spa jet pump.

Hello all. I have 5 g color pool light, 5g spa light, 300 watt transformer for 2 laminars, 300 watt transformer for bubblers. My question is can I get power by using a jumper between all the relays from the same 15 amp breaker in the IntelliCenter? Also I want to run a 3rd pump for the water...

did you end up using the afp-75? Just curious how they are working? We have 2 laminars and 2 bubblers and deciding if we want to use a sep pump.

Thank you so much for the info. Yes we do have a spa and the 2nd pump is for the spa jets. We are in the middle of a pool and backyard remodel so I had them put in an extra suction just in case. So we will have one available. We are not set on running the features while in spa mode so that is...

Hello we are installing 2 bubblers on our baja and 3 laminars. What type of pump should we add for these? Or should we just come off of our Pentair variable speed. All pipes will come up in the red square.

Thank you. I wasn’t planning on controlling each one independent. But now that you mention it I guess I should leave that option open and run one to each.

Hello we are getting ready to install Pentair laminars that will be connected to intellicenter. Here is my layout.....1st laminar is about 60' from the intellicenter, 2nd is about 40' from 1st and 3rd is about 25' from the 2nd. (pic attached). So my question is, do i need to homerun a 1"...