Search results

Thanks for the advice, everyone. I reached out to my new pool guy... he found a used gas valve from an older unit in my neighborhood. He switched it out and it's worked flawlessly. The igniter and fenwall ignition unit works fine and tests.... he also said he saw a blue ring with a conversion...

Possibly. I do see something about a kit, but the descriptions indicate it's more of a replacement for existing models of NG. I looked over the Quick Reference starting at page 13 https://waterlinetechnologies.com/content/Zodiac/JXI%20QRG.pdf and the manual at page 15...

No way... this place would not allow that and is not listed on the PB list. I think this was an error on their part. Notice they also listed a natural gas unit....

I don't normally smell gas. Just that once before it fired up and in the past, occasionally in the same circumstance, if I recall. Today, I went to use it as normal... outside temp about 45-50F. We also noticed if the air blower is on, that the heater is not able to get to full heat and the...

Newish? If I recall, it was installed about this time of year, four years ago.

Thanks, @PoolGate you think it's the wire between the PCB and the RS unit? I was thinking it might be something like the Fenwall board, maybe HSI or something.... I do recall that yesterday, I smelled a small amount of gas just prior to the unit firing on. It does not always come on... for...

It's the four way... there's no 2 way at the top right. I reviewed the workbook while awaiting some feedback... https://www.doheny.com/media/Pdfs/7609-instructions.pdf Page 24 and 25 of the document.... I get down to step 15, I think. If I recall, there's a buzzing but only an occasional...

Bump.... @PoolGate first image, top left in red...

My bad, it's the plaster.... Is there anything I can or should do to repair it?

TFP, I had a JVA issue in the past month that has been remediated but since doing this, I have noticed a sand like substance in the bottom of my spa. Additionally, we found lots of rough surfaces where the gunite chipped or eroded away. I am presuming this was the cause of having to dump large...

Also, today we tried again. It was about 50F or so outside and the heater was turned on via app after spa being turned on for 5m. Went outside and heater did not fire up. Pressed the button and it buzzed a few times but nothing. Turned if off until this afternoon around 60F and did this again...

I am not sure... here's what I have.

Hello Amazing TFP people. Weird issue with the heater that I am still scratching my head on... I think this is intermittent, which makes me think electrical or component related.... In the past few months, if I went to turn on the heater in the Aqualink app, the heater would come on in the app...

@ajw22 you are a great person. Thank you!

There is one that does this for half of what Atlas offers. I built one for a reef tank experiment and the Tentacle T3, with 3 ISE probes and I2C circuits was like $500. The benefit is that you also don't have to deal with firmware and it's bluetooth or wifi. DM me directly for more info....

Apologies on the belated reply... just came across your thread @JPMorgan the answer is yes and yes.... I also know that there used to be... and still is through dealer now, a Fluidra item that was portable or fixed and could be purchased for $200 that did all of this... it works well enough that...

Hello TFP. I'm currently using a zone on my sprinkler system to maintain my pool levels. It works based on a schedule and rainfall, which somewhat helps but is not always accurate and in the colder months, has actually resulted in some unexpected water loss. Today, I have all this Jandy...

Thank you, @ajw22 for your response. I was able to return and refill the spa before the temps dropped below freezing... It seems this may have nothing to do with the heater but rather something that appears to be well known across several Jandy articles and at least one Pentair. Until I looked...

Hello, TFP. I some help before my pool freezes over. About three months ago, our spa randomly went low after using it and accidentally having left the heater on for a full day. The heater has not worked but once since, usually gives off a buzzing sound at best and will not start manually...

And the problem is solved. The pool person replaced the light as requested and did not set the colors to Jandy LED WaterColors. They were set to JandyColors on Lights. For those that may run into this after turning your lights off and on after 4-6 seconds, make sure the lights are set to JL or...

Pool spillover and lighting issue fixed. The pool person has left right after installing the new light. From what I was informed, the lights will sync when in service mode but not on the app. I followed the procedure to turn the off and back on after 4-6 seconds. Is there a way to change this...

@HermanTX I think I found the problem, please correct me if I am wrong. From that thread I referenced, @ajw22 pointed me to move whatever was on Aux3 to Solar, since I have nowhere else for that to go. I see that is not in place in the images I provided above, but had to in order to be working...

I'm also including my settings before anything else gets botched. Here's the lights and various settings in the AquaPure controller. The spillover used to say that where the lights are before the pool guy started messing with that.