Search results

  1. R

    Easy touch programming of spa Air blower.

    That fixed it, I knew it was simple. Thanks so much again!!!
  2. R

    Easy touch programming of spa Air blower.

    Here are the config pages as well as a picture of the panel, pushing the "air blower" button ( #2 ) starts the air blower.
  3. tonypool2.PNG

    tonypool2.PNG

  4. tonypool3.PNG

    tonypool3.PNG

  5. tonypool1.PNG

    tonypool1.PNG

  6. IMG_20200718_175743.jpg

    IMG_20200718_175743.jpg

  7. R

    Easy touch programming of spa Air blower.

    So I have been updating my Neighbors pool with modern Pentair equipment. First and easy touch 4 and SWG. Next I added screen logic. Finally added 2 automated valve. Basically I have everything working, we can turn from pool to Spa mode from either the Panel or from the screen logic interface...
  8. R

    False Low flow light pentair IC40

    The "flakey cell" is not even installed anymore as I got that one from a friend, it's working perfectly.
  9. R

    False Low flow light pentair IC40

    That's what I told him when he said "chlorine Tabs are just so much easier"... Well I disagree, but in this case THANK YOU! I do think the economics for salt cells are not much better than buying Cl tabs. We seem to spend $150/year on "Cells" ($600 every 4 year) and another $100/year on salt...
  10. R

    False Low flow light pentair IC40

    It seemed to work fine for alot longer than usual yesterday, 4-5 hours. I did reduce to out put down to 80% and then 60%, there was no immediate impact however a half hour later I saw the red flow light come on. Not sure how or why that could cause it. Maybe the cell electronics are sensitive...
  11. R

    False Low flow light pentair IC40

    Its 100% with all led Solid and is on/off for about 265/35 cycle, I didn't use a stop watch.... I have already un-jumpered the flow switch as it wasn't making any difference.
  12. R

    False Low flow light pentair IC40

    Yes I agree, about all i probably proved is...If the flow light is Green The cell is probably generating chlorine. For what ever reason it seems to be working fine for that last several hours. It has been showing low flow "most" of the time for the last week at least.
  13. R

    False Low flow light pentair IC40

    Set to 100%, All looks good at the moment... Flow green, and cell light on and a few minutes later cell light off. At 100% should the cell light ever go off? Seems to me that there must be something wrong with the control board on the Cell. Working for a while, then stopping.
  14. IMG_20200609_151847.jpg

    IMG_20200609_151847.jpg

  15. IMG_20200609_151859.jpg

    IMG_20200609_151859.jpg

  16. R

    False Low flow light pentair IC40

    On Remote it says now error..
  17. IMG_20200609_130830.jpg

    IMG_20200609_130830.jpg

  18. R

    False Low flow light pentair IC40

    In the cell section, there are not lights, not a good green one or a check cell light. Pool is about 25k gallon, run it at 40% most of the time
  19. IMG_20200609_125811.jpg

    IMG_20200609_125811.jpg

  20. R

    False Low flow light pentair IC40

    No light is lit on the Cell .
  21. IMG_20200609_125811.jpg

    IMG_20200609_125811.jpg

  22. R

    False Low flow light pentair IC40

    First Cell lasted 6 years. Second Cell lasted 3 years. Seems like no one has came up with a alternate Cell that is Modbus (rs485) linked to the Easy touch. Would be nice to have a alternate choice. It does not appear that the Intelichlor line is up to the standards I would expect from Pentair...
  23. R

    False Low flow light pentair IC40

    October 2016, was installed December 2016.
  24. IMG_20200609_112804.jpg

    IMG_20200609_112804.jpg

  25. R

    False Low flow light pentair IC40

    I soldered the black and red wires together, never cut them just stripped some insulation. So the switch is always closed, but light is sometimes green but mostly red. Cleaned filters, chemistry is all perfect.
  26. R

    False Low flow light pentair IC40

    Having problems with my IC40 generator. Red flow light is on most of the time, but does go green for a while sometimes. I have cleaned the Cell. I have tested the switch with a meter, it seems to open and close red and black wire when I push the metal flapper in the line. I have even soldered...
  27. R

    Good Day!

    Been reading valuable information on here for years, finally decided to register so i can post.