Search results

Same here. I have two in my pool and both have failed. Short of draining the pool and cuttin a hole in the wall i dont know what im going to do. I dont want to go back with the same lights.

I'm looking for a replacement led light.

I have searched the forum trying to find a thread on a replacement for the aqua lumen niche less pool light with no luck. Does any one no of a suitable replacement for this light?

Thanks

No the motor is still quiet. Today the pump is running on low with no issues. But, when I try to run the pump on high is will stop running with the motor being really hot. So I guess the question now is to replace the motor or the pump. I have priced the motor at $300 plus and a new pump at $750.

Now when I turn the pump on high it will run for a few min then shut off completely. The motor will be very hot. So it may just be the motor going bad.

The flow has reduced to the point that I have to run the pump on high most of the time. So a complete pump replacement is in order. I really would like to stay with a Jandy pump since I have had good service out of the pump. I just a little confused on what pump to go with.

I will be replacing my Jandy JHPU 2.0hp dual speed pump this week. This has really been a good pump been running 24/7 since 2008 and have had zero problems. I would like to buy the same pump but the JHPU is no longer avalible. Can someone give me some idea on what Jandy pump to go with? There...

You must be in Bartow or Gordon county for the dirt to be that red. I live north of Gordon myself. Who is the pool builder? Your pool build looks great.

I had a service rep for autopilot come out last summer to check the problem out and while here he put in a new tri sensor to see it would fix the problem. It did not, still had the low flow rate. He checkd the cell and told me I needed a new one. So I bought one and this did not fix it either, I...

PSI on the gauge is showing 7psi on low speed and 17 to 20psi on highspeed

I have a autopilot SWG that is not working. I am getting a check flow flashing alarm and the unit is not generating chlorine. More than likely the power supply is bad, but before I replace it at a $600 cost I need to check the flow rate. The pool builder use Flex pipe when he build the pool 6...

Ok I haven't post on the problem lately so heres the run down. I still need some help form someone who has experience with the Autopilot. I call a service tech that was listed on the autopilot website from atlanta. The guy drove to my house which is 70 miles away from atlanta, check out the...

thanks, Its making cholrine right now so Im not too worried. Im going to call a technican out to check it.

Went out to check the pool this morning and I notice that the red ligth was flashing on my autopilot. It was giving me a check flow/clean cell warning, so I took it a part the strainer was clean and the cell looks good. After putting it back together it now is giving a purifier off/check flow...

Thanks, I'll update after I get the CYA up to where it needs to be.

I have been using the TF 100 test kit since we installed our pool back in 09. I decided to order a new TF 100 test kit because I was getting some crazy numbers with the old one and I wanted the salt drop test and the stir kit. My pool stays open all year with the pump running, I take the Auto...

I tested my water yesterday and the CYA has come up from 10 to 40. I'm going to test the CYA again in a week to see where it is then and determine if I need to add more stabilizer. As for the ph it is staying around 7.2 to 7.4 which is good. I will do a overnight FC test today to see if I need...

I tested my chems yesterday and the numbers are as follows: FC 3.0 CC 0 TC 3.0 TA 60 pH 7.1 CYA 10 Salt 3600 I put the pH and CYA numbers into the Pool calculator and I have a question about the results? It says I should put in 61oz b/w of soda ash and 227oz b/w of Stabilizer, so today I added...

Thanks for the reply. I'm not sure what I really need to do. I got ripped on my concrete decking, the top layer of the decking is flaking off due to the fact that it got down below freezing the night after it was done. I am thinking about doing Kool deck but not sure if this is the right way to...

Not sure if this is the right place but I have a few questions about using tile to cover over a concrete deck? 1. What type of tile is best to use? 2. Is the tile slippery when wet? 3. How do you cover the coping edge of the pool? My pool has the cantilever concrete edge.

Yes

My polaris does not want to stay in the shallow end. It makes one or to passes then heads straight back to the deep end. I pull it back to the shallow end and its back to the deep end. So has anyone else had this problem if so what do I need to do to correct it?

I'll do that. Thanks for all the help.

Thanks for the info. I'm not sure if I need to clean the cell. It was put in last April, I thought I would take the cell out and inspect it. As for the DE I want to filter my pool better. I have a 2hp pump with a 300lb sand filter and I'm not sure if it is doing the best job. Also what is the...

What is the best way to clean the cell on my Autopilot? How do I add DE to my Sand filter.

As of this morning I am now able to calibrate the salt content. The unit was in Demo mode. The unit seems to be working properly. Thanks

I have had the board/card replaced by a authorized service rep 3 times in the past 2 mounths. I am now on the 4th board/card that I installed myself, service rep mailed board/card along with a new cable. This was installed yesterday. I purchased the Autopilot Digital with sc 60 cell software...

Poolsean thanks for the help. This is the one of the reasons I went with the Autopilot. I spoke to a rep at Autopilot and have set up a service call to get the unit checked out.

Just checked my numbers FC 2.0 CC 0 TC 2.0 pH 7.7 T/A 90 CH 70 CYA 40 Temp 86 Salt 3440 I put the Autopilot on Superboots to get the FC up and will be adding some CYA to get to 80. But still having the problem of the Autopilot going to 0%.