Search results

It’s a 2 wire. If you have the same heater that I do, then have you upgraded the electrical board in the heater? It has to have the HP9 kit installed. If not, then it will not be able to switch back and forth remotely without putting in codes at the heater. The support team from aquacal was...

Yes, got it to work. When you want to heat, go into the jandy aqua link and push temp to desired temp above what you currently have, probably at least 5 degrees above. If you want to cool, go into iaqua link and drop the chiller temp about 5 degrees below and click the heat pump button on. It...

Yes, I contacted them. They will walk me through it. Great customer service:)

I am updating my aqua cal heater (SuperQuiet-SQ166R) and adding the new HP9 board so that I can control both heating and cooling from my phone (iaqualink). Currently it is on the 2 -wire function and I can only control heating. I connected the board as the written instructions/video tutorial...

Thanks for the advise in using the liquid chlorine and stirring the pool water. Having had our pool for the past couple of years, we have been using the TFP method and our pool chemistries have been great. Just worried about it getting out of whack now. Thanks.

Thanks. Just found the paperwork and it looks like it is still under warranty. I will ask the pool company who installed it to see if they can replace the pump. I wonder do they normally just replace the whole pump that day or will they try to fix it and I will be without a pump to circulate...

I did a little more diagnostics and although I was getting power to the pump, it seems like the computer board (capacitor) is not allowing power to go through it, which makes me believe the power is not going to motor itself. So it looks like something may be faulty with the capacitor unless...

I have a Jandy ePump Pro Series Variable Speed pump 2.70hp - vsshp270aut

I tried to operate pump separate from aqua link and still nothing (no humming or signs of trying to turn on). I tested the pump leads to see if the pump is getting power with my meter and the pump is getting power. I turned off the disconnect breaker at the subpanel to turn off all power to the...

hi all, My jandy variable pump (2yrs old) is not turning on. I just installed the upgrade HP9 board kit to my aquacal heater to try and get it automated for use by my phone. Heater originally was connected as a 2 wire (only controls heating and not cooling), but I upgraded the heater board so...

Thanks for sending this video. This helpful. Looks like he is sharing the surge protector leads on the breaker.

Thanks for the info.

If I connect the intermatic PS3000 to the 80Amp main disconnect breaker in the pool sub panel, would that provide me with enough coverage if I did get an electrical surge until I have enough time to add a larger sub panel box?

Thanks! No, I do not have any available breaker slots left in the pool sub panel. The surge protectors listed in the document you sent seems to be whole house surge protectors versus if I just want to have a surge protector that is only for the pool equipment. Any recommendations? I have...

I want to place a surge protector that will cover the entire pool subpanel. There is a 80amp double pole breaker for the main disconnect breaker, 60amp double pole breaker for heater, 20amp double pole breakers for lights and pump. I have seen the internatic PS3000, but I’m not sure if I can...

Thanks for sending this. Have you or anyone you know used these before? Any thoughts about how to prevent the the Hayward lights to not leak or short?

I have had my pool for installed for one year with 2 Hayward ColorLogic 4.0 connected to Jandy aqua link system. Both lights have burned out In less than a year. One was replaced and burned out in one month. Warranty took care of it, but worried that when warranty runs out, I’ll be stuck paying...

I left my autocover on with pump and heat pump off from 10am until 4pm. Air temp In the morning was 81degrees and got up to 98 degrees. When I uncovered the cover at 4pm, surface water was hot (101 degrees). Below surface was chilled. I then turned pump on to circulate water and water...

This makes sense thanks. So should I leave the autocover on without pump circulating or autocover off without pump circulating during the day in the sun to have it the coolest?

I have an aqua cal heat pump. Pool water is starting to get to consistently in the low to mid 90's (on occasion high 90s). What is the best way to cool the salt water pool? Run the chiller on the heat pump with the Autopool cover on or off? I like to get it to high 80's (i.e. 88 or 89...

Thanks for sharing the link. I will look this over.

Do anyone know if there are caps to go over inground anchors that are used around the pool for the winter covers? I have a travertine paver deck. I would like to find some bronze caps that can go over the holes of the anchors during the summer time so that dirt/debris do not get into them and...

Thanks for the advice. I spoke to the auto cover people and they said I didn’t need to have a safety cover. Although it would put a beating on the autocover and my have to replace it sooner than if I had a safety cover. I plan to have it measured and priced out for a safety cover this week to...

Thanks for the replies. I think I'm leaning to getting the safety cover. I think maybe the solid to help decrease the chances my pool being opened to a green monster. I assume go with a name brand company with a good warranty is key, right? Any experience with safety cover anchors in...

I have an inground pool with an auto cover and travertine pavers dry set deck. When closing the pool, the company said that I may benefit from having a safety pool cover on instead Of using the auto cover to cover the pool throughout the winter. First, is it necessary to have a safety cover on...

This subpanel has only 8 slots. The heater, main disconnect, and water pump are double pole breakers, which then only left 2 free slots. The electrician did say they had issues before when autocover shared breaker with lights, hopefully this will solve issue. Cross your fingers!

The electricians came and placed the heater, water pump, and auto cover on separate breakers. The lights/outlets and automation system share one gfci breaker. They would have placed the lights/outlets on a different breaker from the automation system, but there were no more slots available in...

Do people have separate breakers in the subpanel for each component (inground pool lights, heater, pump, automation box, salt generator, main disconnect, etc.) of their pool or are there components that can be combined on some breakers? I have a heater, main disconnect, and pump on separate...

Chris, Thanks for the helpful info. I did a quick troubleshoot by turning all breakers off at the sub panel, then turned each one on one by one, and noticed that the light/ auto cover breaker also controls the iaqualink automation to come on. This may explains why when that breaker trips, even...

I have a Jandy VS epump that is connected to the iaqualink. My pool was just installed this past May. Over the past 2 months, at least once a week (if not twice a week) the light/auto cover gfci breaker in sub panel trips, causing the VS pump to also not work. I reset the light/auto cover gfci...