Search results

Thank you. My only issue is that it's $55 shipped for just a seal. Pretty sure that's more than OEM Hayward. Any idea if there are other generic more affordable optioms that will work? It doesn't sound like anyone has verified it yet.

I'm trying to figure out where and what seal to get now without spending an arm and a leg.

Did you or anyone else find out about this? I think I need a seal for my B&D 3hp already :/

I will give that a test. We have been having very sunny 100+ days so I'm sure thats eating up quite a bit. I bumped it up to 25% now.

I think it is 3E23005-700903 but that may be some other designator. Sorry for the delayed response. I did turn down the salt genration but Ive noticed my chlorine numbers are still pretty low.

Genuine. Should it be negative or positive volts/amps or what does that do by pressing +

First reading: -25.01V -6.50A 81degrees F 3400 PPM pressed + then read +24.84V +6.96A 81degrees F 3700 PPM Pressed + again -24.84V -6.86A 81degrees F 3700PPM Im not sure what you mean by the first 7 characters of the cell but it shows 942001E Rev K, T-CELL-15...

Sorry for the delay in answering, its been a busy few weeks. I will try testing turning off the swg for a bit to see if I still feel the heat and the smell. Maybe I'm doing something wrong here but I thought I was shooting for 8 FC with cya near 70 with a salt water pool. Now I will admit...

The original setup is I'm guessing about 10-15 years old. About a year ago I switched over to a salt cell, adding it to the Pro Logic pl-p-4. Perhaps it was bumping it up to 60% or maybe it's done it all along but the other day I was near the box and smelled an electronics burning smell coming...

I got it sorted. Not sure what setting I changed, but it seems to be working as intended now. Thanks to everyone for the help.

Im about to pull my hair out at this point lol. The relay tested bad so I went ahead and ordered a new one. I installed it today and no luck. So I started diving deeper and when I set the Aux2 to filter low speed, theres a click when I engage low speed but the black thing does not pop up and...

So I went back and forth with poolpartstogo and this was stated: Me: At high speed the filter pump relay solenoid black peg gets sucked in, no movement on the others, when I switch to low speed the filter pump relay pops out but the aux 2 relay does not move. Them: If the AUX2 relay isn't...

Alright I got my third or fourth automation panel in today and as of right now, it's not restarting every minute. The new issue is that when I press to filter button on my Hayward pool control panel which is supposed to switch to low speed, it turns the pump off. I hear the relay click and if I...

I really don't have a decent fix in the meantime. I'm using the standard panel right now waiting for a fix.

I got their supposedly fixed panel two days ago. Installed it last night and same issue. They want it back ASAP so they can examine it... So no resolution.

So I was thinking today since there is no resolution in sight. Maybe the calimar panels are good to go and will work on these black and decker units. Maybe I can just ask for a refund and repurchase from somewhere else.

I know I did on some of them but I can't say for certain I did every time. Do you think that could be related? Also, have you expressed to the poolpartstogo team that it's most likely a programming issue?

You are right. One of the panels seemed to work at first and when I got home the next day I noticed the symptoms had started back again as well. I don't know enough about computers to call BS on the solder joint issue but I also agree it would be a bit strange to have a mechanical issue cause...

Quick update. I got my third automation adapter and it exhibited the same exact symptoms. What was strange was when I switched to wiring scheme 2 (which I don't really want to use long term) the adapter worked as it should with no restarting. I advised the guys over at poolpartstogo and they...

Yea I just got a reply from Cody at pool parts to go and he is also stumped. I don't know what the odds would be of having two automation adapter bad back to back or even more strange an issue where it occurs every 60 seconds. It seems like there is something else at play here but I don't know...

That was also replaced. Same symptoms when running on the adapter panels :/

When running the original panel it runs just fine. But Ive gotten 2 adapter panels and they exhibit the same symptoms.

Also, that 5v, is that AC or DC? I was getting 10v when probing it which seems a little high.

As a new data point, I eliminated the pro logic panel and just touched the red wire to the black wire and it ran at 3k RPM for a minute and stopped and started just like before. I'm really scratching my head at this point.

Sorry I figured since we moved from wiring to troubleshooting a strange new behavior, a new thread would be in order. At this point I don't really know though lol. Any ideas guys?

So I got my B&D VSP running just fine with the factory control panel but I've developed an issue since wiring in the automation adapter. Now after running for 60 seconds, the pump will ramp to 0rpm and immediately back to full speed. It will do this both at full speed or half speed setting (Aux...