Search results

In my pool, I have a very big calcium build up in my SWG and my plaster staring to getting rough How can I reverse this problem?

At what water temp does the generator stop making chlorine ( pentair 60 )?

My pool has a yellow stain from alge I have scrubbed it have , I got it because my SWG checked cell, I did this and it was plunged with whits crust, I cleaned per directions and t weeks it is back, What is causing this?

I do not know if I have problem or not. Here is what is going on, I set my easytouch controller for 50% output. on the IC60 all the lights are on ( % lights) and some times the last 2 go on and off. all other lights says everything is ok , flow, salt level all green. Has anyone had this happen?

Is it ok to run fresh water through the generator until I get all the salt levels set. I know this may be overkill, but I have an IC60 on my 24000 gal pool I got it at a less price than a ic 20 or 40, I just could not pass this price up. I am hoping to run it at a low setting so it won't work as...

been slamming my pool now for 4 days keeping at 15 to 25 FC, now when do I let it drop to the 7? Still some alge seen on bottom, I brush it every day. Should I keep the salm at 15 to 25 for a couple of more days? Should I be checking all the chemicals and adjusting them during a slam?

Just starter my slam, adder 2 gallons blerch, how long do I have to wait to check the FC befor adding more to get it to the FC shock level ?

Hi guys, I have a water softener that uses potassium chloride, Does this affect my pool chemicals in anyway?

Hi guys, I just noticed that I have a little rust stain on my new plaster, it is around one of my niches. What do I need to clean it and what to apply to the area that is rusted on the niche so it will not continue?:cool:

Which pump would you recommend for the waterfall ? the feeder line is only 3/4 inch2

Less than a year old just turned on for the first time and it has water in it. Can it be fixed or replaced

I just installed a screenlogic2. now my problems all started, I am running EL Capitan on my IMAC and it can connect all I get is system not found, So I tried it on my laptop with Windows 10 and get the same thing. Also when I look at my serial # on my protocol adapter it only has 9 numbers. I...

I have a question about connecting my VS pentair pump to my Easytouch controller. Do put the 22oAC to a CB so there is power on the pump all the time or through the relay in my easytouch controller. The control wire from the pump is connected to the control BD?

Guys, I have a controller it connects to my easytouch ok, but after a few minutes it goes to this panel is for easytouch it is connected to a PL4/PSL4 And I can not reset it no matter what buttons I push., I have to take the batteries out to reset it. Is this a comm loss? or what?

Can anyone tell me what is the difference between these boards. Is a software or a hardware issue? Pentair board 522524 and pentair 522456 board EasyTouch controller mother board.

Guys, Be careful when getting a Pentair Easytouch Controle , I got burned When I was having my pool re-done I ordered a EasyTouch PL4/PSL4. I took this for a pool and spa setup. Now the problem, trying to set it up I get the heater and pool pump to work but when I go the spa mode the inlet and...

I now that this question was gone through long ago, i just need to find the right link to reestablishing comm. between my easytouch and wireless remote.

I don't know if I am barking up a tree, but here goes, does anyone have a wiring diagram for the (CVA24T 24 VAC 3-wire 25 ft. 180 deg.) valve controller? :confused: It is connecting to an easy touch controller.

Got my pool all done in early Aug. Have kept the chemicals balance according to the pool calculator and a 100 chemical kit. Now I am starting to notice small algae spots starting to show up . PH 7.654 TA 90 CYA 50 CH 325 PUMP RUNS 9 hr a day at 60 gal min. What do I need to do? All FW now...

Hi guys, I just got my new pool turned over to me from the replastering , I did my first check and the PH was 8.4 . Am I right is assuming that I should get the PH stable before adding of the other chemicals? I do not want to ruin my new plaster . I am working with fresh water now, I will...

I just had my pool redone new plaster coping, I did the plumbing and I got the intake and discharge backwards on my hayward valve , do you think I destroyed my DE grids ? I only had it running for about a min or 2.:(

Ok guys I have been reading the forum for a couple of weeks now. I got the taylor 2006 kit and here are my results PH 7.8 CC 4 CH 220 TA 140 CYA 20 FC 4.4 Salt 3400 Do these look ok or do I need more tests and what do you recommend for chemicals Pool Calculator Pool 26000...

Pool store says my pump is putting out too much pressure. I have blown 3 grids i am running 18 lb on my gage ( pentair whisperflo 1.5 hp.) ( hayward DE 60 Pro filter) Has anyone had this problem and how to correct it? Should restrict the flow?

I picked up a Pentair IntelliBrite pool light, but it is for a spar light, my spar light now is a pool light size. Does anyone know of an adapter to put the spar light into a large pool light nicthe. any advise would be greatly appreciated.

Hi guys I am new to this forum. I enjoyed reading some of the problems people encounter and the fixes that are provided. I have a large pool about 36000 gal. and need a new pump. I have been researching the Pentair and the Hayward VS pumps. does anyone have a preference and why?