Search results

Re: You guys have seen this before, Autopilot DIG-220 error You guys are awesome!!! Switched the pump setting and it started working. No idea how it got changed. I can here the fans running again... So, I did this last night. Checked it earlier today still good. just went out and it had...

Re: You guys have seen this before, Autopilot DIG-220 error Josh, thanks, not sure what I was doing wrong, but it worked this morning. OK, I change the cell to sc-60. It still shows the same 0 volts, 11.4 amps. The pump config is set to Remote runs pump. I have no clue what it has always...

Re: You guys have seen this before, Autopilot DIG-220 error I can't get into the installer menu. Trying to hold select as manual say be it does not work. WhAt screen shoul I be on when doing that???? Also noticed it thinks I have sc-48 cell and I have sc-60.

Re: You guys have seen this before, Autopilot DIG-220 error Ok, replaced cable and trisensor. Warning light is off but it is not producing chlorine. Test says salt at 2900, add 22 lbs. temp 84. Cell 0 volts 11.4 amps. Any ideas? I can't hear the fans running like I think I used to hear...

Re: You guys have seen this before, Autopilot DIG-220 error Thanks Sean. I was hoping you would respond. I will order now.

Re: You guys have seen this before, Autopilot DIG-220 error Of course, check it today and light is flashing same messages again.

Re: You guys have seen this before, Autopilot DIG-220 error Ok, removed manifold for 3rd time, reconnected cable for 22nd time, and it decides to work???? We will see, sounds from other posts as it may be short lived but it will save me some bleach at least for awhile! I will update if it...

Re: You guys have seen this before, Autopilot DIG-220 error I used a mirror to inspect the pins, all is good. I read on a post about the wire maybe getting hot or something and a goo coming out? I don't recall seeing this on my cable before. Any thoughts on this? Also read about sensor...

Re: You guys have seen this before, Autopilot DIG-220 error First, thanks for the response.... Cable has been disconnected and reconnected from both ends several times with no change in behavior. Cable physically appears ok. Is it possible to test the sensor or the cable to determine which...

Re: You guys have seen this before, Autopilot DIG-220 error BUMP

My SWG is 5 ohio pool seasons old. Getting a variety of error messages this year since I opened the pool. I am getting the Purifier OFF! No flow. Also getting the Warning bad temp sensor and sometimes getting the add salt xxx lbs. Flow is strong, clear valve seems to be working fine...

Bump.... I brought my pool to shock level for the past 48 hours to ensure that my cloudy water is not an algae bloom. With my light on my pool, the return line water leaves a "cloud" effect 4 feet wide or so. Still no ideas, but I still think it is air.

Thanks for the vaseline tip, of course I was told by a local pool supply store that it would work fine!!! The pressure is normal when the pump is on high, I run 22-23 psi. But, on low the pressure seems low, it barely is registering. It almost seems as if the pump is not functioning properly...

OK All, I inspected the lid o-ring, lubed with vasaline (till I can get a better lube) - Result No Luck I have a compression fitting between the top of the pump and the filter. Removed, cleaned, lubed, replaced -Result No Good I took off the top of the sand filter, cleaned, lubed, and...

I have a two speed Whisperflo pump that I believe I have an airleak, as I can run the pump on high fine, but the strainer basket lowers 2 inches or so after about 2-4 hours when I run it on low. Also, my water is VERY cloudy, at night with the light on it seems obvious that it is just tiny air...

Perfect, I will open it up myself and check and if not I will go with the RGA. I was hoping you would comment. Your support on this forum is the reason I made the purchase. I had a great first year with my pool. I did have an incident early in the year that a family member shut off my...

My SWG was installed last fall when my pool was built, and just before closing this year it began making a relatively loud noise. It is mounted against my wall where my bedroom is, and about 2 weeks ago my wife and I began to be woke up by this noise. We tracked it back to the Autopilot. It...

I am closing my new pool by myself this year after the builder helped me last year. We just blew air into the main drain line (pressurized), and then shut of the valve to trap the air in there. I bought a 6.5HP craftsman shop vac, but can't get enough pressure in there (assumuming it is...

Exactly... See I can read and learn how to do this correctly!!!! :goodjob: I bought the largest cell possible for the SWG also, knowing it should last longer. --Chuck

Jason, thank you very much. I am getting used to the calculator, it is a great tool. --Chuck

My pool has been sparkling clear all summer, I have been just tweaking my Autopilot setting keeping between 3-5 FC levels, and all has been well. 5 days ago it got cloudy, I shocked it (15) but didn't keep it there though, and today it is still cloudy. I thought my shock level was 15, but am I...

So, in going with the o-ring theory. I took out all 3 jets, and took a picture for reference. I used the winterizing winter caps and sealed 2 of the 3 openings off. Then I tried each jet in the fitting left open. None of the jets worked. Did this with the pump on high and low, and with my...

I have 1 1/2 inch piping. I have 3 returns, so measuring GPM that way would be tough.

I don't believe it ever worked. I never really fired it up in the fall because it was too late in the year when I got it all installed, and of course my builder is no longer in business! It does not have enough flow even after a backflush of the filter, I just confirmed that. I will try the...

Waste, I'm sorry, I should have stated that. When attempting to get this going, I do shut of the main return lines so ALL flow is going to the step, and the pump is on high. It puts through a ton of pressure. I have deck jets also and when I have them open, I can shoot water 20 feet in the...

Not that I need my heater right now, but I bought the Pentair Whisperflo 2-speed 1 HP pumps so that I can basically run it 24 hours per day on low, and not have to mess with a timer or anything. Well, my Heater displays a message that it has inadequate pressure on the low setting. This makes...