Search results

I turned on my heater this afternoon. Went to check the temperature and can’t login. How do I turn the heater off without the app?

Went from clear to green in 20 minute! Wind picked up and blew pollen all in the pool!

Still working! Must have been a flow issue. Up about 10 degrees so far!

Not really. Filter pressure was normal. We are getting a lot of pollen now and it was highlighter yellow!

Well, this is strange. I just backwashed the filter and tried the heater one last time and it turned on…. Strange.

No. It shows “remote rs485 online”.

No. I select temp A which is preset to 90 degrees. When selecting temp A the pump rpm’s increase to 2,250 and here the bypass open but it never begins the ignition phase. This is exactly what it did when we first got it and when the pool tech came out, he did something and it worked for a...

Hello! We recently had a Jandy JXI400 installed a few weeks ago. We are using iAqualink for automation to control it. When it was first installed it wouldn’t work when turned on in the app. Pool company came out and changed a setting and it worked great. Now it’s doing the same thing again...

Why does automation have to be so confusing!!

After a long delay in ordering our pool heater, a Jandy JXI400 that was ordered last October…. It has arrived!! It was a pain in the Rear, but hopefully worth it! After the pool company installed the heater we needed a plumber to install a 150’ gas line… Next we needed to coordinate with our...

I just installed the Edge 40 about 3 weeks ago. Average water temp then was 68-73. I started it off at around 60% and the next day my FC went up to around 13! I actually had to turn it off for a few days to let the FC drop. When it return to approx 6 ppm I turned it back on at about 27%...

Haha thanks! Speed is the same. I think I figured it out. We also have a AOP system (i know, I know 🤑) with ozone and UV. I think there was a buildup of ozone bubbles in the bubbler line and reduced the flow. Tested it this morning, bubbler started to go down so I increased the pump speed for...

Okay, 🤦‍♂️🤔😏. .. So, I have a bubbler on the tanning ledge...... it’s controlled by an actuator... I make no changes to the actuator or valve.. and it starts the day strong!! Nice flow!! However, two hours later, the bubbler is at least 2-3inches lower then when first started. Later in...

Good! I made a last minute decision to cut out the tab feeder! I still need to clean up the wires and will post pics of the final install shortly 🤗!

saltwater generator installed! Never done this much pcv piping before! All working well!! Adding CYA’s now!

Another question... When I install the new swg I was planning on leaving the tab feeder installed for a just in case backup and it’s there and why mess with it. The swg will be installed before the tab feeder. I know you can’t mix anything in the tab feeder because of the risk of explosion. So...

Well, I went out this morning to buy the salt for the conversation. I was estimating approx 15 bags so that’s what I picked up. Shortly after getting home my Taylor salt test kit arrived. I did the test and the pool is already at 1,600! I didn’t expect it to be that high! Now I will only...

So a low CSI won’t affect the equipment or the stone coping around the pool? I just need to keep the ph in check then?

Hi all! Im about to convert my pool with a salt water generator! Parts on order and should arrive in a few days. I’ll be doing a self install of the CircuPool Edge 40. I was doing pool math this morning and it appears when I add the salt to the pool the CSI number went off the chart...

Thank you for the reply! So that salt system wouldn’t just plug into this? Sorry if I sound dumb, (my first pool and the builder didn’t want to install a salt system, aka every builder here!!)

Thank you!

I’m looking at this system: https://www.inyopools.com/Products/00000000032574.htm Will this work with iaqualink??

Yes we have automation. It’s the Jandy IAquaLink.