Search results

Ok new test results after a good backwash to be sure I got as much off the filter just in case . Also reduced ph with dry acid Fc 9 Cc 1 Alk 80 Calc 90 Ph 7.4 Cya 0 I think I'm ready to start slam . From all I have read I need only come up 1ppm . I have liquid shock 12.5 % label just says add...

Duraleigh, I take no offense ! I was following pool store advice and I see where that got me ! I will do all of my own test from here on out ! I'm reading all I can and applying all I can . It's the high ph that's throwing me ? If I understand it's the results of shocking ( I was 7.4 before I...

If I'm reading everything correct ( a lot to take in ) For slamming I'm where I should be ? Already cleaned feeder Any harm in brushing liner at this point ?

Ok full results Pool is about 16000 gallons vinyl sand filter fc 11 Cc 1 Alk 80 CalC 90 Ph 8 ( maybe a little higher ) but I did add shock yesterday Cya 0 ( ran this test 3 times ) need to get more tester soon Still suds on surface water surface looks very shiny like oil Lots of bubbles on...

Kim, Thank you ! So here's my plan 1. Full accurate test result 2. No more splash less bleach 3. Clean and rinse feeder 4. Shock based on readings Will suface draining to waste help ? Drop two inches refill repeat , repeat , ect How long do you think it will take to know I'm heading in...

Here's an idea I've been using splashes bleach can this be causing or adding to my problem ? At this level of 10 plus are emzyms useless ( is the high chlorine destroying them ) ?

Duraleigh, Thank you for your response a new Taylor kit just arrived late yesterday . So I will soon report full accurate results . I feel simply better with the fact that this can be solved . The pool store looked at me like I was crazy and stared handing me everything off the shelf . Worst...

Ch 10 + Cc 0 ( pool store said shock it 3 gallons ) Ph 8 Ch 100 TA 50 ( just boosted that today ) Didn't test cya as I don't add any and don't use any chem that have it Sand filter with DE added ( 2 cups )

I hope this is in the correct place . I have an indoor pool I was having foaming issues . Used defoamer ok results for awhile . But soon got out of hand . Did enzyme treatment worked well for a week then back to foam ( not bubbles as much as soap suds ) I'm at my minds end with this ! So I...

Mine did not come with the rope . Says it's an option . I've had 5 kids turned loose in it a few time no foot movement at all . The legs wiggle a little is all ( but thats at the top )

Jason, Thanks for the info . I guess I'll pull out the old ones and hook them up . They seemed to work pretty well . Plug holes as needed ! On a good note the pump is on a timer now . Pool is crystal clear and balance . 85 here today ( Maine ) think I'll just kick back and enjoy the pool...

The heaters were a gift . I do have a set of the 2x20 longer black ones ( few leaks ) I have a 1 hp Hayward pump . In setting I have it in now I see no difference in temp from return . Change setting blow hose off ! Before I hard plumb want to see if these 2 little heaters are even worth it !

If you happen to have this system what position ( or number ) do you put the handle in for heating ? Instructions are awful !!

Good luck . I know it's not much fun getting there but we'll worth it in the end !

I have this to deal with !

Sitting here looking at having a cup of coffee it drives me nuts . If I explain it the wife one more time I think I might be single !

Just don't want to be that guy ! When you look at the picture of the whole pool it looks more out of level than it really is . The wall pattern is not even .

- - - Updated - - -

Thanks for the reply . The leg is dead on left to right just off front to back . My thinking is with some swimmers it may push out a little . Just want it to be safe for the little ones !

Pool is all up and full of water ! Checked level all the way around at every T I'm within 1 inche . All good there . But I have one leg that's not straight up and down when I put a level on it the bubble is just barley in side the marks . If I lift the level ( at the bottom ) about a 1/4 of an...

I see what your saying . Man this little pool is Turing into a lot of work !

Have a deck built for a 24 foot above ground pool . Now have a 22 ft intex . How do I fill the 1 foot gap all around ? Can't move pool closer . Any ideas ?

Thank you for the response ! I found a few post with some info about it . Did you put the straps on before or after you filled the pool ?

Just setup my intex 22x52 ultra frame and there is no rope or loops for one ? Should there be one ? I know they instructions say optional but the picture shows it in place even the video shows it ?

So the ground is level pool is all put together . Long day ! Now my issue is getting the legs to line up with the pavers . Can't see them under the tarp . I'm thinking I could just fold the tarp up behind the legs so I can see the pavers . Anyone see any issues with this ? I plan to start...

Where I'm at - - - Updated - - - Where I'm at , Pavers are all down and leveled . Tried to post pictures but says they are to large .

I'm no expert but have looking to do the same thing . I have a Hayward pump also . I've been told it's a straight cut and hose clamp and all will work . I ran into Wally World today and they have a kit for this ( they don't show it online ) My only concern a pot going with either of those...

So if I'm reading this correct it should still be a simple plug and play . Just use the intex fitting with my Hayward hoses and all should be good ?and if I decide to swap out the fittings just need to make my own gasket ?

Looking at the intex pumps does the 3000 make sense ? For this pool ? Matched with the 15000 salt water system ? Gonna let my Hayward pump sit and see how this works like the plug and play with no cutting or making my own adapters Also does the 22x52 come with the floating skimmer basket or do I...