Search results

I just deleted and readded the chlorinator but it’s still reading high on the instant salt. I tried the schedule on the chlorinator again and it works but it does not update the app or web interface. From the control panel you can see the chlorinator enabled when the schedule calls for it and it...

I have noticed that my salt level is running higher now and have verified that it is incorrect with my handheld meter. I am wondering if I should delete and readd my chlorinator to see if the scheduling begins to work as expected and to "reset" the salinity. Troy

I’ve installed the update and my heater now enables and disables as per the schedule, but my chlorinater does not. What did you do to get your chlorinator to switch on and off with the schedule? Troy

You can confirm if your transformer is putting out the correct voltage (12-14 Volts). Also I think that this is the networked version. Are you using it with a controller? Troy

Hi Jim, For the saltwater generator, have you tried bringing up the pools chlorine level to target level with liquid bleach and then used the T15 cell to try to maintain the chlorine PPM? If the cell is not keeping up, and your CYA level is good I would do an overnight chlorine loss test...

It sounds like the main panel's firmware is corrupted and may need to be sent in. The manual linked above talks about clearing the DDT from MSP to "refresh" it. I have no idea if this will fix it as I have never done it, but if you are feeling adventurous you can give it a try to see if it...

A quick workaround, while not ideal is to set a theme for the heater. Create the theme with the heater set to temperature that you would like the spa to be at and also set whatever equipment needs to be on at that time also. Think of the theme as a snapshot of what is on and off on the Omnilogic...

?? That’s for sure.

I just tested again and it’s down to 32.5 ppm already. So it’s dropping fairly quickly.

Thanks for the help everyone!

So I am not sure where I went wrong in my calculation as I used pool math, but I overshot my slam level by a lot. I was supposed to go to 28, but just tested and I am at 39. Will that high level damage anything? Should I bypass my heater? My CYA is 70.

Thanks Chris!

Perfect. Thanks gonfishin.

This does help. Thank Chris! I do have one more question for you though. This is a picture of my pool. As you can see I have a lot of trees surrounding it. Does this add to the likelihood of algae re-infecting my pool? Troy

Thanks Gonfishin. Can the high chlorine levels damage the furniture?

Thanks for the help Chriss. I have updated my signature. Do you have any advice on the in pool furniture? Also, I test daily and make adjustments as needed while clearing the skimmer basket. Weekly I brush or vacuum along with cleaning pump basket. Am I missing something? Troy

A couple of months ago I started loosing chlorine at a faster rate than usual so I performed an overnight test which failed. I followed the SLAM procedure and everything went back to normal. This weekend we had a storm. I checked my FC before the storm and I was at 7 PPM with a CYA of 70. During...

Perfect! Thanks Jblizzle!

Ok. So I have done a bit of reading here on balancing my pool water. There is one thing that confuses me though. For a plaster pool with a SWG, the recommendation here is to have a TA of 60 - 80. Is that recommendation after calculating to remove CYA? My readings from my Taylor FAS-DPD kit are...

I wanted to post this in case anyone was trying to schedule their SWCG. It does work, once you understand a couple of things. The SWCG must be set to on. The schedule must be within the times of the filter pump (Not starting and ending at the same time). The Omnilogic sets the SWCG to its last...

Ok. I figured it out and just wanted to update this post in case anyone was having a similar problem. The issue is that the schedule puts the heater at the last temperature that it was set to. Since my schedule called for 88F and my last set point was 88F it wasn't showing a change. I assumed...

Hi everyone, Thank you for all of your help so far. I have another question on my OmniLogic that I cannot seem to figure out. I am having trouble with my heater schedule. I can turn my heater on and off manually from the omnilogic and change set points. But no matter what schedule I set in...

It is a GVA-24. I don’t have it set to fully open - fully closed though. I set the internal cams so that it’s either fully opened or throttled. I do have a setting to stop the pump when my valve is changing, but that isn’t really the issue though. The issue is that when a theme is turned off the...

Thanks guys. I am now seeing this. I was able to do the dry run without turning on breakers as stated. Thank you for the help! I now have a schedule question now that I am up and running, but I already started another thread for that on over here: Omnilogic Schedule Help If anyone knows how to...

Hi, I am running an Omnilogic, and I have a question. On my Returns, I have an automated valve which the cams are set to throttle when I turn a feature on. Because I don't have a schedule on the valve though, when I exit a theme the valve goes to a throttled position which is not great for...

For anyone that has configured an Omnilogic, I have a question. On a new build, do I have to wait until my pool is full to power up and start configuration of the panel? I wanted to start the configuration early, but I am not sure if it is ok to do so. Does anyone know? Thanks for the help! Troy

Just bumping this to see if anyone has advice.

I am planning a 10 X 10 Tanning Ledge and am trying to figure out the best way to light it. I am going to do one or two Colorlogic bubblers on the ledge. So I am wondering if the bubblers are off will turning on the lights for the bubblers light up the ledge properly? Or should I put a...

Thank you for the help.