Heater destroyed in 1 month? So confused! [pics]

Jump to latest Follow Reply
schoeps

schoeps

Member
Jun 4, 2023
13
Reisterstown, MD
Glad to find this forum, hope you all can help :)

Had a Raypak heater for 3 years and towards the end of the third year, the heater began to leak and eventually caught on fire and destroyed the entire manifold. Through many, many phone calls, Raypak replaced it and sent us a new one. In just under a month, I noticed the new one leaking in the same way. The service company came out and took the following pictures which were sent to Raypak for review. The previous heater we had lasted over 10 years, any idea what may be causing this?

Other things to note: we have a VSP and a valve for fountains just after the heater. Is it possible there was too much pressure in teh manifold? We are totally perplexed!

Any thoughts appreciated, happy to provide more pictures and info. Thanks all!
 

Attachments

  • Resized_Resized_20230601_135352.jpeg
    Resized_Resized_20230601_135352.jpeg
    710.7 KB · Views: 296
  • Resized_Resized_20230601_140113.jpeg
    Resized_Resized_20230601_140113.jpeg
    714.2 KB · Views: 289
  • Resized_Resized_20230601_141020.jpeg
    Resized_Resized_20230601_141020.jpeg
    382.1 KB · Views: 293
Can you post a picture of your full equipment pad so we can see the heater in relation to the other equipment, including any in-line chlorinators?

Also, do you have your most recent test results including pH?
 
  • Like
Reactions: Mdragger88 and YippeeSkippy
Schoeps, I'm sorry... I didn't take a minute to welcome you to Trouble Free Pools. Hi there!! I'm calling in a BIG GUN who knows this stuff inside and out. I hope he'll be online soon and can answer.

Can you tell us your current water test results? Particularly the TA and pH?
FC
CC
pH
TA
CH
CYA
Salt if applicable

How do you sanitize your pool? Have you put any chemicals in the water?

Maddie :flower:
 
  • Like
Reactions: Mdragger88
Looks like it is getting way too hot.

What is the gas pressure?

Is this propane or natural gas?

What are the old and new model numbers?

Lots of pictures of everything including the gas lines, gas meter, gas pressure regulators etc. would help.
 
  • Like
Reactions: Mdragger88
It does not look like chemical damage.

Looks like excessive flame/heat probably due to excessive gas pressure.

Do you have a tab feeder?

What are the chemistry readings?

resized_resized_20230601_141020-jpeg.500221


resized_resized_20230601_135352-jpeg.500219


resized_resized_20230601_140113-jpeg.500220
 
schoeps said:
Not sure what a "tab feeder" is, it's a salt pool and i belive when it gets low, the service comapny puts tablets in the skimmers.
Click to expand...
Tablets in the skimmers are poison to heaters.

How long have you been using this pool company?

Does your heater problems correlate with changes with the pool company or pool tech?
 
  • Like
Reactions: Mdragger88, Flboy44 and YippeeSkippy
What is the gas pressure?

Is this propane or natural gas?

What are the old and new heater model numbers?

Lots of pictures of everything including the gas lines, gas meter, gas pressure regulators etc. would help.
 
Last edited:

Enjoying this content?

Support TFP with a donation.

Give Support
The tubes do not look like they were exposed to chemical damage, but that is not certain.

The damage looks like excessive heat.

This might be due to excessive gas pressure or maybe slow water flow or no water flow while the heater was on.

Maybe the flow/pressure switch is bad.

Is the heater above, below or at the same elevation as the pool surface?
 
Hi all, thank you so much for the replies, I really apprecaite it. IS the regulator inside the unit or is it that disc thing on the outside in picture 4? Thank you again, I really apprecaite your help!
 

Attachments

  • 1.jpg
    1.jpg
    102 KB · Views: 84
  • 2.jpg
    2.jpg
    108.9 KB · Views: 78
  • 3.jpg
    3.jpg
    86.7 KB · Views: 81
  • 4.jpg
    4.jpg
    117.5 KB · Views: 84
This is the regulator and it means that you have higher pressure to the regulator.

I suspect that the regulator failed and allowed full pressure to get to the heater.

You can have that tested to see what the pressure is at the heater inlet.

1685918180996.png
 
Honestly, that gas installation is scary. Even though the flex line is coming out of a PVC pipe, I can’t image that’s anywhere near being up to code. NG should be buried and straight piped from the source to the heater. All those joints and flex line is a hazard.

I hope you get it figured out and you should consult a plumber with a license in gas work. Very bad things can happen when gas lines are not up to code.
 
  • Like
Reactions: Mdragger88, proavia, HKPoolPA and 1 other person

Enjoying this content?

Support TFP with a donation.

Give Support
You must log in or register to reply here.
Thread Status
Hello , This thread has been inactive for over 60 days. New postings here are unlikely to be seen or responded to by other members. For better visibility, consider Starting A New Thread.
Top Bottom
Back
Jump to latest Follow Reply