919,
I was just expecting to see a 400 or 500 Sq. Ft. filter. In the pic I had wrongly assumed it was maybe 100 Sq. Ft. as it just looks like a small filter.
Thanks for the feedback,
Jim R.
New construction
- Thread starter newbie919
- Start date
I was just expecting to see a 400 or 500 Sq. Ft. filter. In the pic I had wrongly assumed it was maybe 100 Sq. Ft. as it just looks like a small filter.
Thanks for the feedback,
Jim R.
Thank You for checking and the feedback. If I have to clean too often will probably change to bigger and Ebay this one.
A bit worried about the black with NC summer sun to tell ya the truth.
@jimrhabe
When I start running this baby where is the sweet spot on the Hayward Tcell 340 swg? Is there such a thing? 30% 50%? 6-12hrs of run time or 24/7 at lower speed?
There is no such thing. The cell doesn't know anything but what you tell it to do, nor does it care. It's either on, or off. 12 hours at 30% is the same as 24 hours at 15%. It produced FC for 3.6 hours, and 3.6 hours came off its 10k hour expected lifespan.
Stretching the production over 24 hours helps in that you are topped off around the clock and your FC will swing less than a short run cycle SWG.
awesome thank you. 1 more though as always. At what rpm does this baby actually produce? 1250rpm 1750rpm 2200rpm? Just play it by ear and see what works once PB is out of the equation?
No two plumbing systems are the same. Mine works at 700 RPMs. Some need 1200 or 1750. You start low and add 100 RPMs until it turns on. Then add 100 RPMs to account for reduced flow as the filter gets dirty. That will be your SWG speed.
So ocd kicking in. Still under construction. Turned equipment on today. Testing the e20 out. Hate dirty water even just looking at it. Tomorrow will start running water tests to get used to methods.
Last edited:
i
be a clutch addition.Now to start getting dirt out of the yard. 1 truck at a time
Ran it twice total of about 4hrs. Sucked up a lot of the res clay and leaves that had settled at bottom. Pb currently has pool at 75% 8am to 8pm then 90% 8pm-8am. cartridge psi barely registering. Lights work heater is off currently. Turned lights on but water is 6 inches below lights so shut them off asap. Robot is better than I thought. Will
be a clutch addition.Now to start getting dirt out of the yard. 1 truck at a time
Caro325
Well-known member
Thank You Caro. After 6 months wife is interested where she has shown no interest. So it must be going well!Your pool looks amazing
It will only get better as you get the water balanced and the dirt and stuff out of the pool. Well done!
Don’t have the patience needed to sit around and wait for them to clean it
So testing water swg is off just circulating water. No chemicals added yet. Looks like.5-1 on CL and Ph between 7.2 and 7.5. I know pics are hard but best I got until they start adding chems and rest of water.
Just call me Buttermaker. Sitting here skimming by hand. Added 120 oz of 10 percent Chlorine
Ok just logged first practice test results. Will do again when they add all the chems and they finish filling water. May take a dip tonight since e20 is doing such a good job. Temps outside 86 Omni is reading water at 84.
i
got the tfp 100 salt. Is the stirrer supposed to vibrate? I turn it on and it does nothing. Light works.
No. I had mine apart trying to fix it.
It's magnetic and makes the pill / X bar spin silently, but only after the water/sample is added.
Fill the vial to 10ml or 25 ml
Drop in the pill/ X bar
Turn on stirrer.
Thank you. I was bugging out. Have been know to take a few "new" things apart.No. I had mine apart trying to fix it.
It's magnetic and makes the pill / X bar spin silently.
Fill the vial to 10ml or 25 ml
Drop in the pill/ X bar
Turn on stirrer.