Recent content by NUTNDUN

I wanted to revisit this since I realized something I didn't do right. Since I redid the whole equipment pad I had emptied all of the sand out of the filter and removed the laterals. When I reassembled it I am pretty sure I put the lateral screens facing up. Could this cause some issue? I plan...

I would replace the pump. We had a Doheny 1.5 hp pump and our electric bill was crazy and we barely ran the pump but a couple hours a day. Now we have a variable speed pump and run it 15 hours a day and only costs $18 a month to run. I have our old Doheny pump if you want it and want to drive...

If your water is fairly clear and no CC's I would add the baking soda to raise the PH and TA. Even at least half of what pool math shows to get started and add more if needed to get to the correct level. Get your CYA up to at least 20 or 30 and get FC accordingly. It helps that you have the pump...

CYA could definitely be the main culprit. That is a big difference between your CYA levels. I have noticed a big difference in FC loss during the day just being down to 60 from our normal 80. We have had a ton of rain and I am working on raising it back up.

I have been trying different valve settings and doesn't seem to be making a difference. If I run the pump at a little higher rpm (2,200) it pretty much fills the basket to the lid other than a couple of quarter sized bubbles that stay there. It seems like there are bubbles that randomly appear...

Are you bleeding the air from the filter as you prime the pump? Sounds like you might have a sand filter with a multiport valve?

Thanks Jim. I will give that a shot. I may even get lucky and just have to tighten the screws on top of the valves since they are new or maybe it is just a bad o-ring from the factory. I didn't even give it a thought to the valves possibly being an issue and once you said something I realized...

One other thing to note also is I do not have any check valves in the plumbing. I guess technically it shouldn't matter as long as everything is air tight on both the pressure and suction sides when the pump is off the water shouldn't drain back. I will mess with the Jandy valves and also try to...

Jim, I do have two of the Jandy 3 way valves in front of the pump. One for the two skimmers and one to bring the bottom drain and the skimmers together right before going in to the pump. I was having the pump run 24/7 but last night I changed the schedule to only run from 9am to 9pm at 1750 rpm...

I pulled all of the unions apart along with the lid to the pump and applied lube to all of the orings just to see if it makes a difference. We have been having nothing but rain this week with more on the way the next three days so it is a little hard to keep an eye on the water level inside the...

I came across another thread while doing some reading and made me curious about the water level in the pump basket. I noticed if I am running the pump at 1750 rpm or higher the pump basket is always full with no air. However if the pump is being run at 1400 or 1600 rpm it will gradually drop the...

This was the best opening of the pool in the last 7 years thanks to you guys and TFP. We have a couple of stain spots which I originally thought were organic but the spot I tested did not lighten up when I held a puck over it for a few minutes. So we went to the store last night and got some...

I think the way our pool is laid out makes it difficult to get the water to circulate from one end to the other. It is a lazy L shape with the two skimmers, one in each corner of the deep end and one return nozzle in each corner of the shallow end. I might see about getting smaller nozzles for...

Thank you. I will wait to do anything with adding or diluting. Checking it was set on the correct cell was one of the first things I did because of hearing about it could cause damage. Looking forward to the learning process and see how it does. The pool is from the late 70's or early 80's and...

We made the switch to a SWG and variable speed pump this year. Finally got all of the plumbing done and everything hooked up. Opened the pool Monday night and surprisingly it didn't look bad other than more silt settled on the bottom than expected. We did do a retaining wall and the yard around...