Recent content by michaelrj9

Here is a pic of the manifold, the crack is right at the set screw hole. The crack is 11/2-2" long. not sure if I could use a 2" cap or if the tee is a weird hard to find size. Then maybe some glue or flex tape :) for the rest of the crack. I really wanted to remove the cracked tee and replace...

The top manifold where the tri sensor goes into cracked. I can't run the pump like that as too much water is being sprayed out. A new one was ordered today but probably won't be here until at least mid next week or end of the week. I already checked local shops around here with no luck. Can...

I am getting the purifier off check flow message on my dig-220. Things I have checked or tried: 1: level of water in pool is at max 2: skimmer strainers are clean and have good flow, return jets don't seem any different (good flow) has some air bubbles but it has been like that for years...

Are these too far away? Hopefully you can zoom in enough and still be clear to see. Forum would not let me post larger photos

Hope this is the right area to put this even though it is not new construction but all the other places seemed out of place. Long story short I am having a company remove and replace my inground beaded liner but I also need to replace or have someone replace my track. (Or maybe just re-secure...

Looking for some suggestions on what ask for to be done. I had a new liner installed about 3-4 weeks ago. I found a spot on the floor where something is poking from the underneath and I am afraid after sometime the liner will rip. Is it reasonable for me to make sure they remove the liner...

It does have the 3 cell power settings 1-2-3. I think I understand the chart in the manual on how to adjust if the percentage is too high or to low. It says if the FC is higher or lower than normal then if the purifier % is less than 25% do the following a or b, if it is between 25-75% do this...

I am new to SWG's and bought a house that had a Pool Pilot Digital DIG-220. It was a foreclosure so can't ask the owners. I did download the manual but am confused on an important part. I went through the installer menu and made sure everything was correct size of pool power setting etc. In...

It is time for a new liner this year. Any suggestions on what brand, gauge and or anything else that would help? I will have one of the local pool companies do it but just wanted to get some input on what brands I should look for or stay away from etc. Do any liners come with a warranty for...

Re: Need advice on what chemicals to add to get it cleared u FC+CC=TC. The TC of 2.2 posted above is correctly derived from adding the FC of 1.2 and CC of 1. The confusion arose over how the chlorine could be "past 5". Did you test using both the FAS-DPD (which uses the powder) and OTO tests...

Re: Need advice on what chemicals to add to get it cleared u How does your water look? You need to raise CYA a little and shock to get rid of the CC and green per directions in pool school. Water is cloudy not really green anymore it is a slight bluish tint. (it was green before adding bleach a...

Re: Need advice on what chemicals to add to get it cleared u I used this tester in the pic and it showed it is past 5 for the chlorine and the ph was lower than 6.8. These Results below are from the TF test kit: FC is 1.2 CC is 1 TC is 2.2 TA is 20 CH is 30 CYA is 15 (or less I could still...

Re: Need advice on what chemicals to add to get it cleared u Those numbers FC CC and TC are from using the Tf-100 kit the "basic" CL and Ph I posted 5 for the CL and 6.8 for the ph were using the basic daily ph and CL test kit. Mine is model k1000 from Taylor So what should I add. Thanks...

Just trying to get it cleared up from last winter. We let it go thinking we were going to replace the liner. Was green before now is just cloudy. Pool is 16x40 IG vinyl liner with a SWG and its at 3100ppm. The pool has a right angle and pool depth goes from 3' 6" shallow end to 8 ft on the...