Recent content by DeanaR

  1. DeanaR

    Anyone have any ideas on opening this thing before I smash the lid off ?

    Thank you, I was aware that sand doesn’t wear out this was exactly what I was concerned about. I’m no expert but a filter been sat for seven years full of nasties that it previously filtered out plus the junk I filtered out when I first checked the equipment was working can’t be good For it. I...
  2. DeanaR

    Anyone have any ideas on opening this thing before I smash the lid off ?

    Thanks for the info I will have a look into this.
  3. DeanaR

    Anyone have any ideas on opening this thing before I smash the lid off ?

    I know sand doesn’t wear out, I was more concerned about it being clumped together with the stuff I have filtered through it when we were first trying the equipment out. I’ll definitely be backwashing until I get into it.
  4. DeanaR

    Anyone have any ideas on opening this thing before I smash the lid off ?

    Yeah I have already backwashed it a few times but i Thought the sand may have needed changing with it being sat for so long? Like I said I’m new to pool life ha. thank you so much for your input.
  5. DeanaR

    Anyone have any ideas on opening this thing before I smash the lid off ?

    Hi, the brand of filter is lacron. I am trying to get into it to deep clean the sand/ check the amount of sand inside Or replace. I just moved in here in December and the previous owners hadn’t used the pool in the 7 years they lived here so I have no idea what inside looks like. I have Vacuumed...
  6. DeanaR

    Anyone have any ideas on opening this thing before I smash the lid off ?

    Ahh thank you! I have seen it on a few posts and wondered haha. I shall have a look at what I have laying around, thanks.
  7. DeanaR

    Anyone have any ideas on opening this thing before I smash the lid off ?

    What’s a 2x4? Sorry probably a thick question haha
  8. DeanaR

    Anyone have any ideas on opening this thing before I smash the lid off ?

    Hey guys and girls, does anyone have any ideas how to get into my sand filter? I have so far tried tapping the seal, pouring hot water onto it, and using a crow bar as leverage (in the gap used to push not to pry it open) I am stumped! Can I get a tool for this Particular kind? I’ve seen some...
  9. image.jpg

    image.jpg

  10. DeanaR

    Finally getting somewhere!

    Chlorine is currently zilch in the pool itself but suppliers aren’t doing too bad, I guess it’s because not many of us are lucky enough to have pools here. I have some that supposed to be coming tomorrow though so I should be good to go with the slam process, yes I have a test kit that also...
  11. DeanaR

    Finally getting somewhere!

    Hopefully if the weather permits! I’ll still enjoy looking at it even if it’s too cold to swim Haha. I feel like I’m getting to know it a lot better Whilst being in lockdown. I can’t wait to see it sparkle ( eventually) ?
  12. DeanaR

    Finally getting somewhere!

    Just a quick one to say thank you to everyone who replied to my posts this week. I think we Have established that I am a newb but based on advice from this site this week has been very productive! I have managed to get into my pump,simple task to most but two days and lots of tips, tricks and...
  13. DeanaR

    Pleeeaaasseee help me identify my plumbing and valves.

    Thank you, I only have one main drain and one grate, one was the lid from the other one haha, it’s the first time I’ve fully inspected the pool so had no idea until I stuck the brush down and it moved ?
  14. DeanaR

    Pleeeaaasseee help me identify my plumbing and valves.

    Thank you for the advice will definitely be having a play. in Regards to the vacuum hose no it isn’t attached to a port it attaches to the skimmer but I don’t seem to have any suction at all coming from the port that the hose connects to. I have two holes a front one which is the main skimmer...