Recent content by chrisexv6

To anyone who has recently bought an Explorer 30 - did you get the 2 sets of filters (fine and "spring") and if so, where was the second set located in the packaging? Cant seem to find mine....we have all the original packaging and still cant locate them. The fine ones were already installed...

Dont forget the robot uses electricity too :) Your electric cost is so low, I wouldnt be looking at that as a reason to change. Even if you had to run 4 cyles of the Polaris to get your pool clean, thats going to be about 2 bux. Yes it takes more time, of course. There are robots under $1K...

Exactly. There are a ton of ways to look at it....what do you "make" for an hourly wage at work? If it takes an hour to vac your pool, anything less than that hourly wage is (technically) saving you money. But I dont look at it that way. How much is your time worth (not monetary but...

Up here in CT (where everything is expensive), my kwh cost is about 27 cents. So 4.5 kwh = about $1.15. Not bad, IMHO....as long as the Polaris does the job in 3 hours. In another thread I did the math on how much my robot ended up costing me since it died after 8 years. Worked out to...

Had our Blue Diamond for 8 years, this year its no longer working correctly. But I think we all need to preface "years" with how long our season actually is. Here in CT, *maybe* 4 months of use a year. And when I was using it, *maybe* once or twice a week. So 32 months = 128 weeks, times...

Might be a little late, sorry about that.... We did like it up until now. It cleaned well enough, sure it missed a spot here and there but the bulk of it was vacuumed up in one cycle. Id either run a second or just brush the areas that still had some dirt left. Now, after buying the "tune...

This season we started having issues with our Blue Diamond. Have to admit I have never done any maintenance on it other than washing it with freshwater, cleaning the filter, etc. Its never been an issue until now. Reading through the manual, I see a note: "Make sure that your Pool Cleaner...

Pump doesnt lose water when shut off (at least for the 15 minutes I left it off) Dug up some silicone grease and did the pump lid o-ring and the "t-ring" between the union and the pump Put some food coloring on the glued joint between union and PVC, didnt notice anything getting sucked in...

Never checked when shutting down, will do that soon. O-rings are clean, but not lubed (they were brand new but I dont have the recommended Jacks lube....will run out and get a tube) Installer (me!) used the included unions. The o-rings are installed, but I didnt lube them because I wasnt sure...

Just started with my new MaxFlo VSP pump (SP2302). I *thought* everything was OK, but today woke up to air coming out of the returns. When I stop and start the pump, at 3000 RPM there is no air in the pump basket or the returns. After prime cycle it will kick down to whatever V-speed is...

Vinyl pool, Im not too worried about calcium. Been opening this way for a long time and its never been an issue. i do have some liquid though for when Im too lazy to pre-dissolve cal hypo.

Yeah my SWCG is not enabled....it will flash "no flow" even with the purifier set at 1% so I set it at 1% and lowered the RPM until the flashing stopped, just to get an idea of how low I can run the pump. Currently Im just filtering and using cal hypo shock.

Yep sorry about that! I forgot to update profile, I will shortly. I dropped it down to 2500RPM for now. I ran it at 1200 RPM earlier just to see how low I can go without my chlorinator yelling about no flow and 1200 still let it go...I didnt try to go any lower. Ill run outside and drop it...

First season opening my pool with our variable speed pump (MaxFlo 2302VSP). I wonder - what does everyone else do in regards to RPMs? Do I just set it to max and walk away until the pool is clear? Do I lower it off max to same some electricity, but assume it will take longer to clear that...

Update: ran the diagnostic that AquaCal support suggested....kill power to unit for 10 seconds or so, apply power and Boost 24 immediately after screen comes up, then check volts/amps after 25 seconds What I saw was 21V/8.0A then 20V/6.8A then 20V/5A. They said the spike at startup indicates...