Recent content by chris4150

  1. chris4150

    Anyone recognize this pool plumbing part?

    Thank you James and Proavia for identifying the part. Much appreciated.
  2. chris4150

    Anyone recognize this pool plumbing part?

    Hello, I took my salt cell off to be soaked for maintenance and noticed this item, see attached photo, inside the inlet side of the salt cell ratings against the cell fins. Based on where the plumbing filters are, I suspect it's a part that came off somewhere after the main pool filters. Any...
  3. chris4150

    Organic stain cleaning via vitamin c

    I should have mentioned that I no longer use the chlorinator as we went to a SWG. I left the vitamin c on for a couple of minutes and it removed the stain.
  4. chris4150

    Organic stain cleaning via vitamin c

    Hello all, Noticed a light stain forming in the deep end. Knew about vitamin c vs ch puck test from being a member here. Tried vitamin c and the test area turned a whitish color. I have an aqua blue pebble tech pool. Will the viamin c cause any color change to the pebble tech color. It appears...
  5. chris4150

    Gold line aquapure automated salt generator states check system cell missing

    What would I look for on the board to verify if it's the board other than it doesn't recognize the cell.
  6. chris4150

    Gold line aquapure automated salt generator states check system cell missing

    The system is 7 years old and it was unplugged and plugged back in.
  7. chris4150

    Gold line aquapure automated salt generator states check system cell missing

    It appeared to be plugged into the panel. Is there another plug location?. All breakers were on as well.
  8. chris4150

    Gold line aquapure automated salt generator states check system cell missing

    Good evening, My neighbor's saltwater generator is giving the message "check system cell missing". I inspected the computer board and did not see any popped capacitors or anything that appeared burned out. Any suggestions? The system is an aquapure gold line automated system with a t-15 salt...
  9. chris4150

    salt reading showing -3.56

    Thank you James, that was exactly the issue. At some point the panel was switched over to metric. Thank you for your quick response and quick diagnoses. This is why I have been a member since 2009.
  10. chris4150

    salt reading showing -3.56

    Hello, I have a Pentair Swim Pure and I noticed that my salt reading on the panel is reading 3.56. No lights are on stating to add chlorine or to check the cell etc. just the green light power and green light generating. Ive never seen my salt go below 2000 before adding salt and Ive never...
  11. chris4150

    Let the build begin!!!

    You will be fine without the redgaurd. the backer board you used is water and mildew proof once you have applied the mortar for your stone. I just finished my build about a month or so ago. Ill post pics of the build as I havent been on the forum for some time now. Your build looks awesome and...
  12. chris4150

    3/4 of an inch loss in water

    I appreciate all of the replies. I will try the bucket test this evening and check the results 24 hrs later. Ill post back then with the results. Chris
  13. chris4150

    3/4 of an inch loss in water

    Hello all, Wanted to verify if I should be concerned. I noticed that my water level has been dropping a bit quicker than normal. As of recent Houston has been 98 degrees for several days straight, except for yesterday and today it reached 95. Be that as it may, last night I filled the...
  14. chris4150

    Energy Bill...OUCH!

    I was about to suggest the exat things as acroy. After conducting alot of research prior to our current house being built, we decided to upgraded both of our A/C units to 15 seer, radiant barrier roof decking, ceramic tile the entire down stairs except for the master bedroom, double paned...
  15. chris4150

    Hayward Pure Swim SWG panel on the hot side.

    Good deal. I just wanted to make sure that the heat being generated from the unit was normal. If not. I was going to call the installer back out.