Which power cord to get for new pump？

Jump to latest Follow Reply
N

NewPoolLI

Active member
Jul 11, 2022
32
New York
Hello everyone,
I'm seeking advice on selecting the correct power cord for my new pool pump, the Super Pump® XE, Ultra-High Efficiency Pump, 1.65HP (SKU: SP2610X15XE). The pump did not come with a power cord, so I'm looking at these two options:

My previous Hayward pump (1HP) used a power cord with a unique horizontal flat prong that matched my existing outlet (I've attached a photo for reference), but I haven't been able to find a similar cord online. I will replace the outlet for the new cord.
My questions are:

  • Which of these cords would be best suited for my new Super Pump XE?
  • Do I need to set the pump to 115V if I use either of these cords? (I've found this video showing how to set the voltage.)
  • Are there any safety or compatibility issues I should be aware of with these cords?
I prefer using a power cord so I can easily disconnect and store the pump indoors for the winter. While a pool electrician recommended hardwiring it, I'd like to avoid the extra cost and hassle of unwiring it each season.
Any insights or shared experiences would be greatly appreciated. Thank you!
 

Attachments

  • outlet.jpg
    outlet.jpg
    302.9 KB · Views: 9
That type of outlet is used on 240V 30A circuits.

It will take some rewiring to change that location to a 120V outlet.

Or run your new pump on 240V and get the correct plug.

www.electronicshub.org

14 Different Types of Electrical Outlets / Receptacles

Electrical Outlet or Receptacle is the main accessible source of electric power. Learn about 14 different electrical outlet types that are common.
www.electronicshub.org www.electronicshub.org
 
ajw22 said:
That type of outlet is used on 240V 30A circuits.

It will take some rewiring to change that location to a 120V outlet.

Or run your new pump on 240V and get the correct plug.

www.electronicshub.org

14 Different Types of Electrical Outlets / Receptacles

Electrical Outlet or Receptacle is the main accessible source of electric power. Learn about 14 different electrical outlet types that are common.
www.electronicshub.org www.electronicshub.org
Click to expand...
Thank you for your response and thank you for the diagram.

I was able to find this cable https://www.amazon.com/Forge-Cable-6-30P-Replacement-Extension/dp/B0D1DM93GL?th=1 . do you think this will be a good fit? and set the pump to 240v .

Since you said the outlet is used on 240V 30A circuits, does it mean that the pool control box should have 240v to power right?

Thanks
 
NewPoolLI said:
I was able to find this cable Amazon.com . do you think this will be a good fit? and set the pump to 240v .
Click to expand...

Yes.

NewPoolLI said:
Since you said the outlet is used on 240V 30A circuits, does it mean that the pool control box should have 240v to power right?
Click to expand...

What pool control box do you have?

Pool control box can be powered by a different circuit.
 
If you want to be compliant with code NEC 680.8(A), the flexible cord shall not exceed 900 mm (3 ft) in length for pools other than storable pools.

Is the pool pump circuit on a GFCI CB? I do not see a GFCI CB in the Intermatic T21004R box.

You have 240V and 120V circuits in the box.

NewPoolLI said:
I got a new Aquacal HeatWave SuperQuiet SQ200R. before I purchased it, the rep was telling to me to make sure I have 240v power.
Click to expand...

Is that Aquacal Heat Pump hooked up?

I would be surprised if you have enough amperage on the 240V power into the box to add a heat pump.
 
ajw22 said:
If you want to be compliant with code NEC 680.8(A), the flexible cord shall not exceed 900 mm (3 ft) in length for pools other than storable pools.

Is the pool pump circuit on a GFCI CB? I do not see a GFCI CB in the Intermatic T21004R box.

You have 240V and 120V circuits in the box.
Click to expand...
May I try to get a 6ft power cord. I am not sure about GFCI CB.

ajw22 said:
Is that Aquacal Heat Pump hooked up?

I would be surprised if you have enough amperage on the 240V power into the box to add a heat pump.
Click to expand...
The new pump is not hooked up yet. But the pool was using an old Aquacal Heat pump. (rebranded as Swim mores)


Hello ajw22,
Thank you for your assistance. I have a couple of questions about my pool setup that I hope you can help with:

I am considering installing an Autopilot ChlorSync II salt chlorine generator, which operates on 220V. Will my current electrical setup (specifically the circuit amperage) be compatible? The installation diagram suggests connecting the generator to the same wiring as the pump—does this pose any issues?

I also plan to redo the pavers and replace the inground pipes. Currently, the pipes are flexible PVC. Since I am located in New York, would you recommend continuing with flexible PVC, switching to rigid PVC, or is there a better piping option given the local climate conditions?

Thank you for your guidance!
 
NewPoolLI said:
May I try to get a 6ft power cord. I am not sure about GFCI CB.
Click to expand...

Anything over 3 feet is not code-compliant.

If you buy a longer cord you can cut the wire to 3 feet to conform to the code.
NewPoolLI said:
I am considering installing an Autopilot ChlorSync II salt chlorine generator, which operates on 220V. Will my current electrical setup (specifically the circuit amperage) be compatible? The installation diagram suggests connecting the generator to the same wiring as the pump—does this pose any issues?
Click to expand...

It should not. But I have not seen the wiring to know or seen where you intend to connect the SWG power.
NewPoolLI said:
I also plan to redo the pavers and replace the inground pipes. Currently, the pipes are flexible PVC. Since I am located in New York, would you recommend continuing with flexible PVC, switching to rigid PVC, or is there a better piping option given the local climate conditions?
Click to expand...

Use all solid Schedule 40 PVC pipe. Flex PVC is not a better pipe for your climate.

PVC Repair - Further Reading

www.troublefreepool.com www.troublefreepool.com
 
ajw22 said:
It should not. But I have not seen the wiring to know or seen where you intend to connect the SWG power.
Click to expand...
autopilot manual - Installation Steps

I was told by their tech to do figture 7
If using a 230 VAC configuration:

  • See wiring schematic located in the inside panel of the device.
  • Connect power to the LINE side.
  • Electrical conduit (rigid or flexible) must be used and installed as per NEC guidelines.
  • Circuit Protection: Two-pole 20 AMP device for 220 V installations, at the electrical panel.
  • Input: 220 Watts (2 AMP) or 220-240 VAC, 50/60 Hz, 220 Watts (1 AMP).
  • See Figure 7 for basic wiring to equipment.

1747689037921.png

Thanks
 
You must log in or register to reply here.
Top Bottom
Back
Jump to latest Follow Reply