Bought new house with pool, sequence of fixing the problem
- Thread starter Xiaosong83
- Start date
- Jun 24, 2021
- 16,041
- Pool Size
- 29000
- Surface
- Vinyl
- Chlorine
- Salt Water Generator
- SWG Type
- CircuPool RJ-60 Plus
WHEW!!!
Leave them off. Permanently.
Great. Salt for the fusion soft should be 3000-3500. If the cell is happy (showing in range), then you are happy. Only use the Taylor, making adjustments. If taylor comes back at 2800, leave salt alone, but know that your real salt is 2800 and cell is happy and will make chlorine.
3100 is just fine on the cell. Leave your salt alone for now.
Post the pics and list your equipment in your signature. From that we'll work on steps to start the cell.
Create Your Signature - Further Reading
www.troublefreepool.com
Leave the mineral cartridge out.
How are you testing salt level? You stated you do not have a Taylor kit to test salt. Normally the AquaPure sensor is within 500ppm of the actual salt level (when using a Taylor test kit - my experience) - so to be off by 1000ppm tells me however you tested salt level may be off.
- Jun 24, 2021
- 16,041
- Pool Size
- 29000
- Surface
- Vinyl
- Chlorine
- Salt Water Generator
- SWG Type
- CircuPool RJ-60 Plus
@HermanTX He has a taylor kit for salt on the way.
@Xiaosong83 Can you show me your pump schedule?
You need to raise FC now with liquid chlorine. Get it to range for your CYA. Link-->FC/CYA Levels
If you are running your pump 24/7, turn on the chlorinator to 25%...that should give you 3FC per day.
Then adjust your SWG so that your FC stays in range for your CYA in the FC/CYA tool/chart.
@Xiaosong83 Can you show me your pump schedule?
You need to raise FC now with liquid chlorine. Get it to range for your CYA. Link-->FC/CYA Levels
If you are running your pump 24/7, turn on the chlorinator to 25%...that should give you 3FC per day.
Then adjust your SWG so that your FC stays in range for your CYA in the FC/CYA tool/chart.
I am testing with a pH/salt probe from Amazon that is similar to the one sold by TFtestkits so I guess I'm not sure how accurate it really is compared to the salt cell sensor which says 3000ppm right now.
It runs from 7am.to 8pm. I'm not quite sure how to set it for different speeds for different times yet.
Yup, done. I should be around 6 because I just added 1 gallon of 10% liquid chlorine
Ok, that is a good place to start. What do you recommend for speed schedule? My pool pump does 70gpm during priming and 50gpm at 2500rpm.
Show a screenshot of your Schedule.
With your current VS speed set up, when in Pool Mode the pump will run at 2500rpm. With a SWCG, you should be able to lower that speed. I ran mine at 1500rpm and it activated the flow switch on my AquaPure 1400. We can show how to lower the speed and still have the SWCG active.
You can change Speed 4 - note I would change this Label to something that makes sense such as Mid Speed, to either a higher or lower speed. Then in the Schedule process, you select ADD and then select Speed 4 (or whatever label you set), then set a start and stop time, then tap SAVE So the speed will change when the start time is reached.
However there are a couple of key rules
Always have the Pool speed as the lowest speed that you want to run as that is the default speed. Currently it is set at 2500rpm and is the lowest speed but I think you should be able to lower it more and still be Ok with the SWCG.
Always set the Filter Pump schedule to be the longest duration you want the pump to run. Let’s say you want 14 hours so the Filter Pump would be set 5am to 7pm. It will run at the Pool Speed.
Set any other schedule to be within the Filter Pump times. So for example, you want Mid Speed (my label which is set for 2750rpm) to run for 4 hrs. Then schedule Mid Speed from 10am to 2pm.
The pump will turn on at 5am and the Pool Speed (say 2000rpm), then at 10am the pump will automatically ramp up to 2750rpm, then at 2pm the pump will ramp down to 2000rpm.
When 2 schedules overlap, the pump will run at the higher of the 2 speeds. That is why you want to have the Pool speed set as the lowest speed for any given time.
The AquaLink system will not run 24 hrs (unless Jandy made a change on their latest revision). So you have to have the pump scheduled something less than- I had mine set from 5am to 4:45am (23 hrs 45 mins). I had the Pool speed at 1500rpm and set 2 schedules daily to ramp up to increase skimming speed. My SWCG was active for the full 23 hrs and 45 mins as 1500rpm was sufficient to activate the flow switch.
Focus on the FC now but when you want to set up the schedule - just ask. But show your current schedule so it is easier to guide you.