Looking to repair two vertical supports

yakob97

New member
Apr 14, 2025
4
Albany, NY
Hi all, first time poster here. Wife and I bought a house in the fall and it came with an above ground pool, already closed up. Come the late winter/spring I noticed that the top rail is lifted up in a specific spot (it was actually lifted much more than in the pictures), might have been due to frost heave? There is a lot of ground water in that spot.

The other thing I noticed is that the two vertical uprights in that spot seems somewhat broken, one to the side of the deck, and one under the deck. The outer one (the one not under the deck) seems to be sort of hanging, secured somewhat by that support going diagonally into the ground. I was literally jiggle the bottom of that upright at the bottom. The one under the deck seems a bit more secure, but a part of it is sticking out of the ground on the bottom.

I'd like to fix this so it's ready for the summer. Other than these two spots, I don't see much else wrong with the pool. The cover was very weak and broke over the winter, causing a bunch of leaves to fall in. Someone else said the stress of that could contributed somewhat, I'm really not sure. Although I'd guess not, since it seems the previous owner already did some hacky stuff to fix that area once before. You can see that those two supports are attached above the spots they're supposed to be, and i'll note that piece of wood pushing on the vertical support under the deck seems to be bearing some sort of load.


Any and all help is greatly appreciated! I also have a video that shows all of this in greater detail, but I couldn't upload it here. Maybe I can upload that elsewhere and link it here.
 

Attachments

  • photo_5181736407943720618_y.jpg
    photo_5181736407943720618_y.jpg
    391.8 KB · Views: 10
  • photo_5181736407943720616_y.jpg
    photo_5181736407943720616_y.jpg
    284.9 KB · Views: 11
  • photo_5181736407943720615_y.jpg
    photo_5181736407943720615_y.jpg
    182.6 KB · Views: 11
  • photo_5181736407943720614_y.jpg
    photo_5181736407943720614_y.jpg
    311 KB · Views: 10
  • photo_5181736407943720613_y.jpg
    photo_5181736407943720613_y.jpg
    298.9 KB · Views: 9
  • photo_5181736407943720612_y.jpg
    photo_5181736407943720612_y.jpg
    318.5 KB · Views: 9
  • photo_5181736407943720620_y.jpg
    photo_5181736407943720620_y.jpg
    295.9 KB · Views: 9
Welcome to TFP! :wave: Made any progress on replacement parts? Perhaps one of our members will recognize that manufacture, or if you see some markings, post them here for everyone to see. Certainly seems to be some whacky stuff happening around that stair/decking area. Might call for a full drain, inspection, and level. Hard to tell from the pics how involved that repair could get.
 
Hello! Thanks for the response.

I have not made any progress on replacement parts. I have a pool guy coming on Monday to take a closer look. Someone else I asked stated that it's a "swim and play pool out of New Jersey", that has been our of business for a few years. He also said he's been unable to get parts from them.

I wonder if I could find replacement parts that are similar enough to work. I don't mind if it's a little bit jerry-rigged, i'm not looking to fix it for years to come, just trying to have it usable for a couple years or so, until it makes sense to either get a new pool or get rid of it.
 
Are those supports wood or plastic?

If you are a good woodworker you may be able to fabricate a similar support using pressure treated wood.

Then you have the issue of how you jack up the pool to get a new support in place.
 
Are those supports wood or plastic?

I think they're metal actually. I'm not a "woodworker" per-se but I've definitely done some woodworking in the past when necessary. I'm sure I'd have all the necessary tools to do that. Good idea!

Regarding jacking the pool, I was planning on getting a jack anyway. I imagine it wouldn't be too complicated if I had one.
 
So this is a different brand (aquasport) but it should be similar. The upright needs to attach to the belt which is counter balanced on the other side.



Screenshot_20250418_114023_OneDrive.jpg

I like Allen's idea. Cement a 4x4 on each side with the belt shot to brace the lateral forces, then build your cross brace and upright from there. Maybe sister it to the existing upright which can stay tied into the top rail.

Screenshot_20250418_114048_Chrome.jpg