Search results

I wasn't aware radiant pools did deep ends. Great advice I will google it. I'm just outside of Toronto in Canada!

Following, considering a deep end as well. I was told to stretch the liner I shouldn't go more than 52" deep as the liners are universal.? Not too sure this is the case.

Thank you pigeon for the quick reply. I was reading about the ledge and slope. Do you have a buttress free pool? To be dead honest (may sound crazy) I'm not too concerned about the warranty. There are soo many factors to getting any warranty work done anyway. How deep is yours? Is your pool a...

Thank you joeself. I believe the buttress free pools have straps from side to side. I also understand a deep end will void manufacture warranty. Is this true. I guess it makes sense.

I've decided to upgrade my intex pool with an oval aboveground pool approx 16x24. I read somewhere that you can put a deep end in an above ground pool with an expandable liner. If so how deep can it be? Has anyone done this? Thank you Tim

Hi Casey, thanks for your reply. I believe your correct. I was just hoping that someone tried it with success!

Hi all, I have an 18 ft x 9 ft x 52" intex ultra frame pool. I was wondering if anyone has attempted to put a deep end in these pools. I have an extra liner ( I bought the exact same pool kit off Kijiji for a dime). Wondering if I could either dig a sloped deep end, say two ft deeper on one...

My saltwater systems shows I have good flow.

Hi, I have the same problem with my mastertemp 250. Did you have any issues with taking apart the canister to access the heat exchanger?

Here is a pic of my thermal regulator

I wondered if the flex line was the issue as its only 1/2". Yes opening the canister, I do have the red high temp silicone sealant as well. Yes just pressure wash the calcium out. Yes thermal regulator looks ok.

I can see I would need to replace the gasket and o rings, what else would you think I may need. I've already had the manifold apart with no issues, everything was clean. Tested the sensors and reinstalled. Thank you for your reply!

Hi all, I wouldn't have a pool without this forum. A big thank you to everyone! <br /> I was wondering if any of you have attempted to take apart and clean their heat exchanger. There is an excellent 2 part 'how too' video on you tube with step by step instructions...

No corrosion at all. The entire heater seems very clean.

I will check now, thank you. The keypad is facing the house to keep kids fingers out of the controls!!!!

Manifold was pretty clean!

Took the manifold apart and found the thermal regulator was stuck open. Cleaned it put everything back fired it up and it worked again for about 2 hrs. Then E05 code again. I have one on order. I will try to get a lazer temp reader as well. Any other ideas out there?!

Woke up to an E05 service heater code. Darn!

That's a very good point. I started it today, ran for an hr, then tried again a few hrs later and it's still working fine 4 hrs later I only keep my pump running for about 5 hrs a day, so im wondering if me turning it on and off once a day it's tripping something.. I'm going to leave my pump...

Hi Zrock! Thanks for the reply. I changed the exhaust sensor a fee weeks ago. I have it running right now, runs for about 45 mins to an hr then trip's to E05. Arrrgh!! The heater was doing the same thing at my friends house. So I don't think the run has anything to do with it. Wondering if...

Hi, where do I start, I was given a Pentair mastertemp 250 it's about 7 yrs old. Worked fine for a few weeks, now it only works intermittently. Comes on for about an hr then shuts off with the E05 code. Tried the stack flu sensor, tried acid washing the calcium out.. Still nothing. Help...

This US fantastic advice. Thank you for saving my summer!!

I'm trying to find any information on how to acid wash my pool heater. I have a Pentair mastertemp 250. My flow is being blocked by calcium build up apparently. Anyone out there acid washed thier heater or pool equipment? How do I go about it?

Thanks Dan! I spoke to a Pentair representative, he figures I have calcium build up in the heat exchanger. Hence the high temps in my stack. I agree with you, I feel the sensor is doing its job. I'll start another thread asking about acid wash your heater!

Hi All, I have a Pentair mastertemp 250 with an E05 code. I've replaced my stack flue sensor and I still get the E05 code. My wife tried the heater yesterday with no luck. (E05 code) I tried it last night and it worked fine for about an hr and a half until the E05 code came on. Checked this...

Hi, I used the click clack mats under my ultra frame pool. Works like magic, soft and comfortable. The kids klick knack mats. Good luck

Hi all, I have just acquired a petrosun thermodynamics solar collector. It is 4x8 ' 3.5" thick with copper and aluminum fins. Has anyone ever seen, used or have one? Thank you kindly Tim

Re: Intex Ultra 16' with Haywood Heater, Intex Sand Filter & Hi blue fish, did you connect both sand filter and swg together? How is the flow rate? Thank you

I live in Canada, the shipping is the same price as the unit arrrg!!!! I may try to either disconnect the cartridge filter underneath the unit or connect the two together. The separate swg has a flow rate of 1650. I figure I should be able to connect the two together and take out the cartridge