Hi All,
I had a pool installed late last year, quickly became frustrated with advice from my pool shop that seemed a bit lackadaisical and inconsistent, and found TFP. I soon saw improvements, thought my pool was a crystal clear dream, yet saw FC dropping all the time. Finally followed the SLAM process (which I thought was unnecessary given my water was so clear) – and my goodness!! What I thought was clear water was actually a murky swamp of horror, and probably the source of the spate of ear aches my youngest daughter suffered (havent admitted this to my wife or kids! The pool has been crystal clear, with no loss of FC overnight, for a few weeks now.
Thanks for building such an informative and helpful website, it's a very selfless and lovely thing
I’m half tempted to paste TFP flyers near all local pool shops and save others the annoyance I went through!
Anyway… gushing rants aside, I do have a few issues I’m still unsure about despite spending a long time reading Pool School and further reading articles…
Firstly, PH. The Pool Math program suggests a target of 7.2 – 7.8, whereas Pool School’s recommended levels says 7.6 – 7.8. Not sure why there is a discrepancy between the two? Anyway I’m at 7.4. Would you helpful people recommend bumping up and trying to keep between 7.6 – 7.8, per Pool School's recomendation, or just leave it?
Second… CH. I have a fibreglass pool with SWG. Pool School recommends between 350-550 – acceptable minimum of 250. Whereas Pool Math says 220 – 320. I’m sitting at 250. I've had minor leaching from coping tile mortar, although will coat with pool grade silicone so probably no issue going forward. I have a gas spa heater, it has developed a noticable and annoying whine – perhaps scaling? Further reading on CH and gas heaters reading says 200 CH is a good compromise to avoid scaling… should I keep at around current level, or even drop to 200? Seems like damage to heater is a greater concern than leaching from the shell? Sorry, if this is too longwinded or complex a question. I’d ask my pool shop, but figure it’d be as useful as asking my dog.
Third… TA is at 125, against a recommended 60-80. However, Pool School says not to worry. Also my PH is pretty much stable. So presume this is OK?
And finally!!! My youngest gets sore eyes… could trying to maintain FC nearer to 4 or 5 assist?
If needed, it’s a fibreglass pool/spa with SWG… fairly consistently CYA at 75, FC 6.5 & CC b/w 0 – 0.5. PH 7.4, TA 125, CH 250, generally 29c (84.2F) all the time.
Again, thanks so much for all the advice you've assembled, and for breaking down fairly complex topics into bite sized chunks that even plebs like I can understand
I had a pool installed late last year, quickly became frustrated with advice from my pool shop that seemed a bit lackadaisical and inconsistent, and found TFP. I soon saw improvements, thought my pool was a crystal clear dream, yet saw FC dropping all the time. Finally followed the SLAM process (which I thought was unnecessary given my water was so clear) – and my goodness!! What I thought was clear water was actually a murky swamp of horror, and probably the source of the spate of ear aches my youngest daughter suffered (havent admitted this to my wife or kids! The pool has been crystal clear, with no loss of FC overnight, for a few weeks now.
Thanks for building such an informative and helpful website, it's a very selfless and lovely thing
Anyway… gushing rants aside, I do have a few issues I’m still unsure about despite spending a long time reading Pool School and further reading articles…
Firstly, PH. The Pool Math program suggests a target of 7.2 – 7.8, whereas Pool School’s recommended levels says 7.6 – 7.8. Not sure why there is a discrepancy between the two? Anyway I’m at 7.4. Would you helpful people recommend bumping up and trying to keep between 7.6 – 7.8, per Pool School's recomendation, or just leave it?
Second… CH. I have a fibreglass pool with SWG. Pool School recommends between 350-550 – acceptable minimum of 250. Whereas Pool Math says 220 – 320. I’m sitting at 250. I've had minor leaching from coping tile mortar, although will coat with pool grade silicone so probably no issue going forward. I have a gas spa heater, it has developed a noticable and annoying whine – perhaps scaling? Further reading on CH and gas heaters reading says 200 CH is a good compromise to avoid scaling… should I keep at around current level, or even drop to 200? Seems like damage to heater is a greater concern than leaching from the shell? Sorry, if this is too longwinded or complex a question. I’d ask my pool shop, but figure it’d be as useful as asking my dog.
Third… TA is at 125, against a recommended 60-80. However, Pool School says not to worry. Also my PH is pretty much stable. So presume this is OK?
And finally!!! My youngest gets sore eyes… could trying to maintain FC nearer to 4 or 5 assist?
If needed, it’s a fibreglass pool/spa with SWG… fairly consistently CYA at 75, FC 6.5 & CC b/w 0 – 0.5. PH 7.4, TA 125, CH 250, generally 29c (84.2F) all the time.
Again, thanks so much for all the advice you've assembled, and for breaking down fairly complex topics into bite sized chunks that even plebs like I can understand