Jandy Aqua Pure SWG Error Codes 125 / 194

Jump to latest Follow Reply
Z

zzed

0
Oct 28, 2017
19
houston, tx
I have a FSOFT1400 Nature2 Fusion Soft Salt Generator & Mineral System. I started getting codes 125 / 194. The Cell was pretty corroded and salted up, so I purchased a new cell.
I am still getting these codes after the new cell is replaced. Is this something a DIYer can troubleshoot and repair or should I call in a technician?
 
zzed said:
No, is there a way to check the cable or the connection to the cell?
Click to expand...

You could remove it and run a continuity test with a multimeter. But the cell end frequently gets corroded. I seem to remember that my cell came with a new cord. Also - do you want your old cell? I would be glad to cover shipping if you don't.
 
JamesW said:
You should always replace the cord when replacing the cell. What cell did you get? Usually you want to get the whole cell kit with the 1400 cell, trisensor and cord. Can you show the old cell and cord and the new cell?
Click to expand...
The middle plate was pretty bad and not much left. Now that I look at it the trisensor is bad too. I will purchase a new one. Thank You
 

Attachments

  • IMG_1658.JPEG
    IMG_1658.JPEG
    376 KB · Views: 18
  • IMG_1659.JPEG
    IMG_1659.JPEG
    464.7 KB · Views: 17
  • IMG_1661.JPEG
    IMG_1661.JPEG
    603.4 KB · Views: 17
  • IMG_1662.JPEG
    IMG_1662.JPEG
    400.2 KB · Views: 16
  • IMG_1663.JPEG
    IMG_1663.JPEG
    274.9 KB · Views: 15
  • IMG_1664.JPEG
    IMG_1664.JPEG
    515.3 KB · Views: 15
  • IMG_1665.JPEG
    IMG_1665.JPEG
    479.9 KB · Views: 19
  • IMG_1666.JPEG
    IMG_1666.JPEG
    356.6 KB · Views: 18
  • Like
Reactions: JamesW
Maybe a bad cord.

Check the voltage and current.

1707682171585.png

1707681930909.png

Aquapure 1400 121 Error

I got the 121 error on my FusionSoft a couple days ago. I cleaned the cell and the sensor and the cell ran fine for about a day. Not this morning, it is back. It is still producing chlorine I can see bubbles out of the returns and the display also says it is on. I think my salt may be a little...
www.troublefreepool.com www.troublefreepool.com
 

Jandy Aquapure PLC1400 End of Life or Can I Make it Last Longer?

The pool did get a little cloudy and smelled a little 'off', but no algae growth. CC was pretty high initially, (can't remember exactly but I think 3-4ppm, when the highest I've ever had before is 0.5ppm) and FC was low at 0.5ppm. You might have gotten some ammonia if bacteria ate the CYA...
www.troublefreepool.com www.troublefreepool.com

You should test the voltage under load.

With the cell under full load you should read 22 to 28 volts DC.

I would make two jumpers to go between the spade connectors with a bare spot on the wires to test voltage.

You need some stranded wire, (2) 1/4” female spade connectors and (2) 1/4” male spade connectors.

Disconnect the connection and insert the jumpers.

Connect the meter leads to the bare spots and then check voltage to the cell when the cell comes on.

Be careful to not allow the bare spots to make contact with anything.
1707682288649.png

1707682300309.png


1707682326257.png

1707682359311.png

1707682380739.png

1707682390389.png
 
PoolGate said:
You could remove it and run a continuity test with a multimeter. But the cell end frequently gets corroded. I seem to remember that my cell came with a new cord. Also - do you want your old cell? I would be glad to cover shipping if you don't.
Click to expand...
My board was bad so I purchased a new Jandy TRUCLEAR11KU TruClear Salt Chlorinator Kit. I have the old Aquapur 1400 along with the new cell and cable which I intend to sell. Are you interested?
(Aquapure Housing, Old Salt Cell, New Salt Cell, New Cable)
 
zzed said:
My board was bad so I purchased a new Jandy TRUCLEAR11KU TruClear Salt Chlorinator Kit. I have the old Aquapur 1400 along with the new cell and cable which I intend to sell. Are you interested?
(Aquapure Housing, Old Salt Cell, New Salt Cell, New Cable)
Click to expand...

Sorry - no I was just looking for a used Nature2 cell as my cell plates are good other than the center plate.

BTW: That TruClear is a known trouble SWG. Make sure you register it if (when) you need warranty work. The cell frequently dies early. Especially if your water parameters are not spot on as it is very sensitive to calcium buildup.
 

Enjoying this content?

Support TFP with a donation.

Give Support
PoolGate said:
Sorry - no I was just looking for a used Nature2 cell as my cell plates are good other than the center plate.

BTW: That TruClear is a known trouble SWG. Make sure you register it if (when) you need warranty work. The cell frequently dies early. Especially if your water parameters are not spot on as it is very sensitive to calcium buildup.
Click to expand...
I have used plates as well.
 
You must log in or register to reply here.
Thread Status
Hello , This thread has been inactive for over 60 days. New postings here are unlikely to be seen or responded to by other members. For better visibility, consider Starting A New Thread.
Top Bottom
Back
Jump to latest Follow Reply