As was the case a couple of years ago, I find this thread again to be very helpful. Though not the handiest of men, I followed the instructions as outlined.
Again, the pictures for step 4 were very helpful. I had to use two vice grip pliers - one, as showed in the picture, and another at the end of the pump as a second stabilizer. As before, it took quite a bit of time and patience. Also, for me, steps 7 and 8 were very difficult. Getting the old seal out took a lot of time and the metal was really deformed by the time I got it out. I think I managed to get it out without damaging the plate, but getting the replacement properly seated took another great deal of time (for me) and the suggestion of a dowel was much appreciated (step 8). I am going to wait a day before filling the pump with water and turning it back on.
One thing I did notice, this time, is that I was greeted with a burst of chlorine gas - or that's what it seemed like. I do have a chlorinator for my pool and as soon as I noticed the leak, I greatly reduced the time I allowed the pump to run. Initially, I set the pump int "service mode" and let the area dry so I could properly ascertain the leak. Though I had everything off, maybe there was chlorine (gas?) released once the system was open. Regardless of the source, I did step outside and let everything air out for 20-30 min before going back in, and the air was much better. Has anyone else encountered this?
Though the leak I had this time wasn't as flowing as the previous leak I had (in 2014), it seemed to come from the same place. So, I guess the question I have is this - I replaced the seal about 2 years ago. During this time, I noticed how beat up and, in some areas I'm getting rust. Though we didn't buy this house from the original owner, I'm assuming I've got gear that is, at least 10 or so years, if not older. What is the average life span of these pumps? I posted pics with information on my pump on this thread: Leaking equipment
I think I may consider getting a new pump in the next or the season just after next. It could be that I am either not very good at repair, or even the equipment is starting to require more attention and for piece of mind, maybe I just replace it. Would appreciate any thoughts/opinions on this.
Thanks for reading, and thanks again for this helpful forum and helpful threads.
Again, the pictures for step 4 were very helpful. I had to use two vice grip pliers - one, as showed in the picture, and another at the end of the pump as a second stabilizer. As before, it took quite a bit of time and patience. Also, for me, steps 7 and 8 were very difficult. Getting the old seal out took a lot of time and the metal was really deformed by the time I got it out. I think I managed to get it out without damaging the plate, but getting the replacement properly seated took another great deal of time (for me) and the suggestion of a dowel was much appreciated (step 8). I am going to wait a day before filling the pump with water and turning it back on.
One thing I did notice, this time, is that I was greeted with a burst of chlorine gas - or that's what it seemed like. I do have a chlorinator for my pool and as soon as I noticed the leak, I greatly reduced the time I allowed the pump to run. Initially, I set the pump int "service mode" and let the area dry so I could properly ascertain the leak. Though I had everything off, maybe there was chlorine (gas?) released once the system was open. Regardless of the source, I did step outside and let everything air out for 20-30 min before going back in, and the air was much better. Has anyone else encountered this?
Though the leak I had this time wasn't as flowing as the previous leak I had (in 2014), it seemed to come from the same place. So, I guess the question I have is this - I replaced the seal about 2 years ago. During this time, I noticed how beat up and, in some areas I'm getting rust. Though we didn't buy this house from the original owner, I'm assuming I've got gear that is, at least 10 or so years, if not older. What is the average life span of these pumps? I posted pics with information on my pump on this thread: Leaking equipment
I think I may consider getting a new pump in the next or the season just after next. It could be that I am either not very good at repair, or even the equipment is starting to require more attention and for piece of mind, maybe I just replace it. Would appreciate any thoughts/opinions on this.
Thanks for reading, and thanks again for this helpful forum and helpful threads.