Search results

I have determined that I have a fried Jandy AquaPure Power Interface PCB (Large) board. Looks to be a simple part to replace. Any recommendation for a reputable "online" replacement part company?? Thanks in advance

thank you sir.... maybe i need go directly to #3 1. pull & clean generator 2. get water tested 3. be patient

Nope, no codes..YEA water temp is around 65. unit set on "boost" ..day 2 Water is clear...... Note this was my first time to run system all winter. my next potential steps: 1. pull & clean generator 2. get water tested 3. be patient

James, Thanks in advance. I have attached pictures... on the picture labled B immediately to the left of the white connection there are two lights "A" and "B". the "B" was flashng but of course it doesnt seem to be now. DUH

Aquapure SWG, my firmware is 02110A10, which if i understand correctly is program "A". Remote controller unit shows "A" however when I open the controller panel and view the board it appears to be flashing "B". Now I am CONFUSED.. Tested chlorine with the handy dandy WALMART test kit...

my firmware is 02110A10, which if i understand correctly is program "A". remote controller unit shows "A" however when i open the controller pane and view the board it appears to be flashing "B". CONFUSED.. need to get water professionally tested but WALMART test kit does not show chlorine All...

ordered a NEW cell.... installed an running fine......

another year and another challenge. so this year i went thru my usual pool opening cycle..... cleaned pool, changed filters, bought a new robot (not planned), added salt, put system into boost cycle...... Everything looked and tested GREAT. WOW, i am happy........then NO chlorine.I am getting...

currently a toss up between "Speedy" and "Road Runner"....dang thing is FAST

My Dolphin Nautilus Plus CC arrived today. Now to kick the kids out of the pool, so it can begin its maiden run.

After replacing, over the past 3 yrs< most of the guts to our 7yr old DirtDevil Rampage/Tigershark, the motor has died! so we are moving on!! Recommendations????

THANK YOU for the assistance....video was helpful. through the process of elimination we have decided that it is a motor box issue.....burial will be at noon, replacement being ordered! - - - Updated - - - THANK YOU for the assistance.... through the process of elimination we have decided that...

Having the same issue.....any words of wisdom

I have a 7 yr old Dirt Devil Rampage/TigerShark that will not move. It begins to "cycle up" then just seems to shut down. I have replaced, over the past couple of years the belts, bearings, rollers etc. Power Supply has power. Suggestions?????

Having similar issue. 2 yr old 1400 cell & A/C cord (3 prong). Salt3.2, lot of rain recently, cleaned cell when problem initially showed up, seemed to help but now it is back. pushed the "reset" button on daughter board, again temporary fix. code is back again. producing chlorine but still...

what would you say is the average life of a cell? this one is only 2 yrs old.

i am getting the 120 error code on the reverse cycle only... i have cleaned the cell, all seems good. cleaned the electrical terminals..all seems good. cell is producing but at a low level. thoughts & recommendations??

if you open the control box, is there a large "motherboard" and a small connecting board "daughter board"? on the "daughter board there is a small white button, actual looks like a dot. this is the reset button. push it...should reset your system...i just reset mine after a thunderstorm

if you open the control box, is there a large "motherboard" and a small connecting board "daughter board"? on the "daughter board there is a small white button, actual looks like a dot. this is the reset button. push it...should reset your system...i just reset mine after a thunderstorm

Pool Clown is .....AWESOME! I replaced my Jandy SWG this year along with rebuilding the DirtDevil and replacing cartridge filters. Could you guess this is year 5, but any way......... In March after replacing the SWG, I kept receiving error codes and THANKS to Pool Clown, I learned of the...