Search results

This is the linked selection - - - Updated - - - LMAO! wrong forum

Thanks a bunch. I reset it.

Had my unit unplugged for the winter and today when I plugged it in it was in service mode. What does that mean? Thanks

Thanks guys. I'll go another route

I think I could have debris stuck in one of my skimmer pipes. Is it ok to pour liquid plumber into the skimmer to see if it will dissolve what may be clogging the pipe. I have one skimmer. When I shut off the main drain the pump will sucks all the water out of the skimmer line then it fills...

The water temp sensor on my Intellitouch will not re-calibrate to current temp. I checked connections. It reverts back to old setting after I change the temp and press the menu button. Any suggestions? Thanks Roy

The capacitor I want to "borrow" is a 25 from my whisperflo fountain pump and the one I want to replace on the whisperflo filter pump is a 30.

Can I temporarily use a 3/4 hp pump start capacitor in a 1 hp pump? that is until I can get a new one Monday.

As well as my light problem in another thread my pump is now acting up. Turned it off to switch sand filter to backwash and the pump would not restart. Not prime but I mean not turn back on. It sits for a few minutes and then clicks on by itself and then clicks off. It never actually starts...

I dont have a transformer I have a Intellitouch

Water got in housing and bulbs went out. I took it apart and cleaned it up and put new bulbs in. Bulbs are not working. What would would be damaged from the water that would prevent the light from from working. Is there a repair kit for the electrical part of the light. I dont need a new...

Thanks guys. I turned my generator down from 40% to 20%. Ill just wait. My pH did read at 7.5.

How do I lower FC so that I can get accurate pH

At what point should I start adjusting for CSI? How old should the plaster be? Thanks Jason

If I adjust to the number on the right then the reading "potential to become corrosive". How do I know what number to adjust to? Thanks for the response.

I am confused about the CFI numbers on the pool calculator. My pool: 20,000 gal. Intellichlor Salt Generator Plaster surface (new plaster 3 weeks old) FC 5 pH 7.5 TA 120 CH 340 CYA 70 Salt 3400 The CSI number on the left is -0.28 and reads "balanced" The CSI number on the right is -0.32 and...

It says to add 5 drops of the green solution and then add 1 drop at a time of the other(?) until it turns red. Does this mean until the whole solution turns red or just the drop that goes in it. I am up to 20 drops and the solution is still green however I have noticed that the drops have a...

Thanks a lot for the info. I didnt consider the board being mostly residential so forgive me if I came across as rude. I certainly did not mean it that way. Thanksagain. Roy

i cant believe noone on here knows this answer. Please!

What is the approximate sf coverage of a 1 portland to 2 marble dust mixture? Thanks

How much does a bag of Diamond Brite cost and how many sf? Thanks

Thanks for all the help. My pool has 5 returns and two skimmers and I wanted to elimate one due to some remodeling I am doing. It sounds like 4 returns will plenty and I could get by with three. Thanks

are needed in a 22000 gal pool

1. What type of mortar should I use to apply the new tile 2. What color water does a very dark almost indigo blue plaster create 3. Also what is the ratio of white portland cement to marble dust for plaster and about how may sf do you get from a mixtue. Thanks

Thanks. I am replastering my pool and can't decide which color to do.

I thought so. Thanks.

I cannot decide. Right now it is white. Beautiful when went in but began showing stains. I think I would like gray but most gray pools I have seen have streaks or random discoloration. Well? Input please.

Can tile from Lowes or Home Depot be used in a pool or is pool tile made specific for pools? Thanks

After 24 hours with main drain plug in I am still losing 1" of water 1/4" being evaporation. Very frustrating. What is the best "syringe" to get to start dye testing? It has to be a structural leak. As I said all lines were pressure tested a few months a go. Thanks for the help.

I pulled the cover off yesterday and plugged the pipe. I will see how it goes today.