Search results

Hi, I just want to follow up on this to see if anyone came across similar issue. At first, I thought it is working again, however, it ran for line few minutes and stop. We have to use the Prowler app to run manually then it works but we have to stand around there and manuaver the robot around...

Is there reset button after lift the motor up? Or lift up and off its connector considers as reset?

I followed the video and it seems unscrew and rescrew, would that reset the motor?

Thank you all for all the suggestion. After taking the impeller apart and did some cleaner, it seems the impeller can spin now after several tests. I tried a few time more and see how it is under the water. Everything else check so hope for the best.

Here is my second attempt to turn on, this time the impeller does not spin anymore. I can see the wheel spinning back and forth. So is our impeller gone bad?

I have no idea what to expect here. Does this mean something? Should it run continuously? I first turned out and it seems like it runs for about 20 seconds or so and then stop.

Do these look ok? I don’t see any slop but once again, I might not know what I am looking at.

Thanks for your suggestion. I didn't actually remove the impeller, I just open enough to see the impeller to make sure there is nothing stuck there. So I assume I can just turn on the robot and see if the impeller is running? Since the wheel kit is out of stock, how can I tell if my current...

Hi, We purchased our Warrior SI from Marina pool almost 3 years ago and now it stopped working. Basically, it worked back and forth for a little bit and then stopped running. We installed this Prowler app to our phone to remotely run the robot and when we looked into the app, it displayed...

Update - after checking the RS-485 cable, it appeared that is the issue. The cable somehow got loose at the pump end and after plug it back in, everything is back to normal. Thank you so much for helping as I have learned a lot since I raised the question. Hopefully I won’t feel intimidated...

The pump is just Intelliflo VS and it’s 8 years old. Our waterfall pump is Whisperflo High Performance Pump. I just checked my VS pump again and guess what? I don’t see the Dislay Not Active anymore when in Auto mode. That means it is lost communication somewhere between the ET and pump...

Yes, we have a separate pump for the waterfall and it’s just a single speed pump if that makes sense. And yes, I can use the remote to turn waterfall, lights, and other features on and off. Ir appears that I can start/stop the pump as well but then nothing happens with the pump. When you say...

I read another thread and my understanding is that if the pump display indicates “Display not Active” when in Auto mode, it means the communicating buss is working properly. Where else can I check? We did had a severe thunderstorm the night before but I don’t recall we have any power outage...

Yes to all. They are set to pool at 2100 rpm and pool high at 3300 rpm. Everything was normal and I didn’t make any changes whatsoever. My water pump can communicate with ET because I can control it from my remote. Thanks.

My pool is almost 10 years old. It has always been working in AUTO until today when I noticed my pump is stop running. I check my pool schedule in ET and everything is correct. I do noticed my pump's clock is 30 mins behind my ET clock. Regardless, my pump should still run by schedule I set...

I have IntelliFlo® Variable Speed® High Performance Pool Pump. The pump seems to work fine.

Correct, the pump display show DISPLAY NOT ACTIVE when in Auto. When I change to Service, then the display is active and I can then start/stop the pump

No, I don't have ScreenLogic, just the Easy Touch remote that is communicating with EasyTouch outdoor panel. The issue here is although the outdoor panel indicates the pump is running on the screen, it's actually not running. If I change to Service mode, then I can manually go to the pump...

My pump stops running when it’s in Auto mode although everything seems to be up when I check my Easy Touch. I tried to reset with the breaker and it eventually started but then stopped after a few mins running. But then when I turn to Service mode, I can manually start the pump without any...

Thanks very much for the detail explanation. My pump is currently running at high speed (3300) from 8 am - 8 pm which I think is too much and unnecessary. Please correct me if I'm wrong here. This is why I am looking to set different speeds at different schedule that can still to make...

I have Pentair Easy Touch remote. After spending some time searching, this is what I plan to do (I guess I need to run long hours especially with Texas heat) 5 - 6 am - set at 3450 rpm (using Pool High circuit option) 6 - 12pm - set at 2200 rpm (using Pool circuit option) 12pm - 8pm - set at...

I have to Google what it is but doesn’t look like I have that. My Easy Touch is wireless which just communicate to the trans receiver. I don’t recall we set up any wireless with it before.

We have Pentair IntelliFlo VSP and we have always set at high. No SWG and heater/spa also set at high but only when we use it. What are some other speed that everyone is using?

Hi, I have Pentair VSP and I have been running for years at highest speed for 12 hours a day. I have also read somewhere that you can run at low pump, maybe at 1000 ppm. Is that right? With electricity cost nowadays, I hope I can save a few bucks here and there. What is your recommendation...