Search results

Here is the plug .

I'm closing my wife's pool and when I unscrewed one of the jacuzie seat jets ,it will not unscrew . The outer housing that I grip will turn as well as the jet part but will not come out . There is resistance when turning it to unscrew it but it will not come out . Any ideas ? one is the jet and...

The panel is outdoors next to the pool feeding off of my barn's 200 amp panel .

I forgot . The bonding wire is not connected to the panel . Does it need to be ?

The bonding wire is under a screw at the bottom of the end plate of the motor . The neutral from the cord is under a screw at the top of the same end plate . The panel is a CH 125 amp 12/24 panel , BR breakers .Separate grounds and neutrals . ....... I just looked in the panel and there is a...

The pump is 208/230 v 8 amps. I'm using 12 ga. , SJ00W cord . I have hooked the 220 dbl. pole gfi breaker up , but when I flip the breaker on the gfi trips . I disconnected each load line individually to check to see if the load lines were the problem,still trips . I took the plug apart and it...

Well I changed out the 20 amp 220 breaker for a gfci breaker . I had to move the pump outlet to the back of the electric pedestal to be able to get close enough to use a 3' cord . I had to go with a smaller diameter cord for the pump so I could use the correct connector for the motor . Almost done !

Should I put a gfci breaker on the low voltage transformer line also ? Pump , 220 gfci breaker ? I'm having a hard time finding a 1/2" fitting to fit the SO cord going from the receptacle to the pump. Can I use a 1/2" threaded plastic termination ,push the cord into it and silicone it in place...

Time for the electric on my wife's pool to be done and the electrician hasn't shown up so I am doing it myself . I ran conduit from my barn , 50' away , to a treated 3x3 pedestal for the 60 amp panel and boxes . I have a gfci plug for the ionizer and convience plug . I have 2 led lights going...

Well I had the factory rep out to look at the pool awhile back ,he said everything was ok with it . I gave up trying to get it the way it should be . I have the retaining wall built around half of it and the concrete poured . I told the concrete man I wanted the smoothest broom finish he could...

There is about 18" of water in the pool now . There is still a low spot at the top of the ramp . I didn't walk around in to feel for soft spots .

He said 1.5" was the difference in height around the pool that is industry standard ", but that they try for 1/4". I was gone all day today but they worked at digging under it . I don't know what they accomplished .

I Texted the installer that there is a 1" high spot on the one side and he said to stop filling the pool at the top of the first step .

The factory rep is coming next Wednesday to look at it . The pool is filling up now . I got in it this morning with no water in the shallow end and there still a soft spot and a low spot . I checked the top of the pool for level and there Is a 1" higher area on one side . Meanwhile I can't do...

Well the installers were here again yesterday . I wasn't able to be there so I couldn't watch them . I'll get in the pool today to see if it is solid . They left the hose on last night , but I turned it off until I can make a judgement call . Last Saturday the installer called me asking about...

It sticks out of the ground about 12" on the shallow end and 20" on the deep end so I could get natural drainage under it . The pool is back filled with a berm of sand and gravel around it . The crew showed up today and drained 3' of water out of it. I was not there to watch and see what they...

We are having a 16 x 40 Sun Fiberglass pool installed in our backyard. While the salesman was selling us the pool I told him that I wanted the pool to be parallel to the house .Before installation day I layed out the pool area where we wanted it to be and I stripped the topsoil off to save it ...