Search results

Could you please share your experience on switching to the RJ-60plus? Thanks!

Thanks for the reply. Here are some update. 1. On Saturday, it was starting producing Chlorine, it increased the FC level from 2.5 to 6 ppm by running about 10 hours. CYA is around 30-35 2. On today(Sunday morning), it stopped producing Chlorine again even with 100% and no error code. I...

I think my pool is ready, I did an OCLT, lost less than 0.5ppm, there is no CC, pool water is clean this morning. I set the cell running at 100% since 7am in the morning. Upon checking the water 9 hours later, the FC level has dropped 0.5-1 ppm. It seems the salt cell is not producing any...

Hi I am currently on the Jandy iAquaLink 3.0 IQ30-RS with PLC1400 SWG, if I switch to the CircuPool RJ series SWG. Do you know if it is possible to continue using the iAqualink web interface to control the SWG? Thanks in advance

I remember before when the SWG is on, I can see tiny little bubbles coming out of the nozzle. Now, in case all generated chlorine gets consumed, should I still see the little bubble that coming out of the nozzle? which I did not see and that makes me concern about the status of the cell.

I have the TF-100 test kit refilled in Aug 2024. Thank you, will perform the SLAM and check.

Hi Expert, I have a Jandy PLC1400 purchased in May 2023(1 year and 11month old). I found it recently stopped producing chlorine as I have it run at 100% overnight for 12 hours and no change in the FC level. I wanted to confirm if it is really the cell is bad or other things. Since my last...

Just to update, there is no o-ring between two halves of the union, but there is a round rubber gasket at the end of on half, when the union is tighten, it seals on the flat surface of the other half. Another thing is I noticed this morning, there is small dripping of water at the filter...

Hi Jim, Maybe you are right. It was installed by previous owner, I am not sure where it was originally from. I would assume it was installed by the pool company who installed the pump. I cleaned the o-ring at the thread end goes into the pump as that is where I saw small leaks. I did not...

I removed the union from the pump, cleaned up the o-ring and sealing surface. Put a little magic tube on the oring and tighten it up. It stopped leaking.

https://www.troublefreepool.com/threads/intelliflo-pump-is-leaking.247412/ was this your post?

@Rocket J Squirrel Hi Rocket, I noticed the same leak on my pump outlet. Just want to confirm that you remove the union and apply some tape to stop the leaking? Was there any oring failure? Thanks!

Hi Jim, Thanks for the reply, how long does the self-test normally take? It looks to me the self-test has past because after it blows water out the top initially, the robot still moves at the bottom of the pool for about 5 minute, acting like it is cleaning, the mobile app shows the cleaning...

I have a S300i about 2.5 years old. It started to have the following issue recently. When starting a new cleaning cycle, it moves back and forth, then the impeller will start pushing water but only for about 15 seconds. The robot would keep moving for about 5 minutes with impeller not rotating...

Thanks for the reply, I did a lot of testing and troubleshooting and think I found the root cause. Looks like it was the cable swivel that interrupts the power to the cleaner, maybe the metal pole inside the swivel have gone bad.

Hi Pool professionals, I have a Pentair Prowler 920 cleaner stopped working and I am trying to figure out which part is malfunction. Below are some observations Yesterday, the robot cleaner stopped working about 1 minutes after I turned it on and I was not able never turn it on after. The...

I bought it from internet and installed myself. The downside is no warranty if not installed by the authorized retailer or professional company. The upgrade installation was fairly easy. It was just a simple swap the board and install the new attena. The most time consuming part for me is to...

Finally upgraded to IQ30-RS and everything works fine now. One question is the iAqualink system Date/Time is still manually set, I thought it should automatically sync with internet time when connecting to Wifi. Am I missing something? Thanks a lot!

Thanks you for the information. I am also think about upgrading to a newer system. For the iAqualink3.0, will the iAquaLink 3.0 iQ30-RS Web Connection Upgrade Kit( the one shown below) work with my other equipment(pump, heater, SWG, light, etc)? This is will be just a swap with the current...

ok. As I am still an amateur on maintaining the pool, I post this on the forum hoping to hear the options from many of you experienced pool professionals. So based on what I described, this is most likely because the malfunction of the controller board?

Yes, it has been replaced. The diagnostic information in the remote also shows Controller Battery OK. I believe it is something else Last night, it starts to go into the "bricked" status around 2am, and did not resume until this morning 9am

I do not have a a spa-side button. This is the front panel when it is working. or should should I look inside?

Hi Experts, I have a Aqualink PDA PS8 that controls my pool pump and other equipment, and it was programmed to run every day from 8:30am to 7:00 pm. However, recently it seems have some issues and what observed made me very confused. Earlier this week, I noticed that my pool would started...