Search results

Thanks! I’ll play around with changing the positions. It’d be nice to be able to keep the hot water in while still being able to circulate water to the pool sometimes.

Is there a way to have 3 programed positions on the spa valve? When the spa is turned on, the spa valve automatically opens and pump outflow goes only into the spa. When the spa is turned off, the valve closes half way and allows cold water to replace the hot water in the spa. I would like...

Thanks. That’s going to be a tough one to get to. Not sure it can be cut without removing the deck and framing along with the equipment on top. It’s not under pressure and can be stopped when I apply pressure with my finger. Do you think plumbers putty jammed in the hole wrapped with rubber...

Thanks for the info. I think I may have found a culprit. I went to the equipment deck and heard water I removed a few deck boards and saw water springing from a conduit pipe. It must have been nicked. Any ideas on why water is running through the conduit? I believe it may be wiring to the...

It does overflow and it seems we have gotten a fair amount of rain. It feels like an abnormal loss and I’m worried something else may be going on like a leak.

Since owning our pool, I have to add about 60 lbs of calcium increaser every spring when opening. This is the first spring opening with salt water and Ive had to add over 600 lbs of salt. Is it normal to lose this much salt and calciu?

Thanks HermanTX! I really appreciate that. Your suggestions were great. I raised the filter and put a bypass on the heater. Everything seems to flow better now.

Thanks everyone for the help! Just got everything hooked back up and no leaks so far! Other than my booster pump making a buzzing noise and not turning on, everything else seems to work. Now to get a salt test to see how much salt I need to add.

Looking at it, I’ll get a new valve and orient it at the pump so it has a straight run to the filter. I’ll put another valve with a check valve to bypass the heater.

Thanks. Gathering all the parts now. The concrete pad is too small. Once I move the heater back to make room for the SWG, it’ll be sitting in the dirt. Also, water runs over the area during a heavy rain. I think raising everything will help protect the equipment.

Good question. I’m not sure why there’s a valve there. I’ve never had to operate it.

Thanks. I’ll try to label the pipes this afternoon. Basically, the three on the right are spa and skimmer suction and the three on the left are the spa output and 2 pool outputs. I don’t close the pool in the winter. Great idea on the heater bypass and thanks for the reference. I didn’t know...

Now that I have the electrical figured out for adding the IC60 thanks to the help form here, I’m looking to get advice on what changes I’m thinking about making to the plumbing. l’m building a deck for the equipment to sit on since I have to move the heater back a few feet to make room for the...

Got it. Thanks!

Thanks everyone, that worked! I can go into the pump menu now in service mode. I can’t believe I didn’t realize it wasn’t wired correctly for this long. I guess when I installed it and everything seemed to work correctly, I thought all was good. So now for the chlorinator power center, I just...

Thanks!

I traced the wires back from the pump. They are wired on what looks like the load side of the relay (circled). Do I just move both over to the line side (arrows)? Looking for confirmation before I do it. Thanks.

I haven’t been getting any errors since I installed it a few years ago. I am connected to the com port. I control the pump with the app when I need to change speeds. The only thing I thought was odd was that when the pump fist starts up, it goes full speed for about 10 seconds. I’ll check the...

Thanks. I put it into service mode and no display on the pump. Probably my fault, because the original pump was a single speed pump and I didn’t change the wiring. How should I change it up?

I just got the IC60 kit from Polytec. What’s the correct way to wire the power center to what I have. I’ve searched, but haven’t found anything that makes sense to me. Would it be best to put the box in place of my Eclipse and moving the wiring around? Thanks.