Search results

Shoot! I had Gap Time at 50. I apologize.. Guess I missed that while focusing on loading the script. Changed to 10 - original script works now (and better than my modified one). Where do I send the thank you?

I do think it drifts fast on clock, but not super bad (ie.. I adjust seasonally to correct). My device is the EW-11A, which I understood was just acceptance of 5-36V vs 5-18V. Here's a snip of my setup screen. Confirmed iOS app works!

strangely, I think I got purely lucky with the 6/60. going to 5/50/100/200 or 10/50/200, and even other small changes around the 6/60 seem to make it worse. I can deal with a bit of repeated sending if necessary.

it does not, and the Windows App only works with the P4 mode box checked - so you got that one addressed. correctly. Any suggestions on the timing? I can experiment and see if there is a sweeter spot that gets even more consistent response.

I replaced the script with a modified one.. changed these variables. TIME _GAP = 6 KA_NEXT_TIME = SYSTIME + 60 - TIME_GAP DT= DT+60 and IT WORKED! Have seen a few times where I had to click again on the windows app, but haven't had a total failure again! EDIT - removing script - note to...

nothing... I did my best quick repeated press on the keyboard, and in the tcp app.

I do appreciate the help so far. Is there something I can try through the monitoring app on sending, or other ways to adjust timing and see if I can get something to stick? Probably time for me to make some attempts on my own, or validate that the EW11 is receiving the signal and it is getting...

Troubleshooting success again! I checked the P4 mode box in settings, and am getting the display text coming over. Turning on the filter on the local panel sends the signal that the pump is on, and the Filter button goes bold. I cannot seem to get the windows app to accept input either...

Thanks for all the help! Apparently, I am stuck in a string of having issues. Now the Windows download is not responding - "Retrieving information from the Microsoft Store"

should I be able to send a hex string from the EW11 - TCPUPD app that I downloaded the hex from?

Certainly happy to try whichever, at least for testing purposes. Currently, I get an error on the Windows Version link you posted, but will try again in a bit to see it is live.

Sorry, I don't have any other remotes. I did copy over and divide the hex out by the start and end codes that I read. Perhaps this helps. Let me keep looking for where I saw the reference, believe it was part of the home assistant boards for the integration and others that had some similar...

sorry - I wasn't sure how to save them so I added a .txt. Is this better? Edit - I may have a P4 versus a PS4. I had only pulled the pcb board part number and know I only have 2 aux switches, but the control interface box does look like the p4 version. That might be my issue, seems I read it...

I have, and also exported the script and confirmed it is the same as the load. Flipped my A/B wires around to confirm that wasn't it - the TCP monitor on that then went to complete ASCII character mess and the emulator would not show the display info, so reverted to what I had done on wiring...

Thanks much! before I checked the 'showHex' box, I see the display info, afterwards - lots of HEX that I'm not quite following. I performed a sequence of Filter on, lights on, aux2 on -- aux2 off, lights off, filter off. First file via main control, second via app. If I read the decoding...

Thanks Mark, I went straight to the iOS app and think I am making progress - got the EW11 up, script loaded, and on the app I do get the feedback messages from what is on the LCD display. The status changes as the filter pump kicks on as well. Doesn't seem to accept input from me though, so I...

Hey folks, been reading for a while and have decided to give this process a go. I downloaded the windows installer, but am having a lot of security issues where it doesn't seem to want to allow an install - is there a trick to that? Hoping this will work for my PS-4, we shall see. Thanks for...

I'm estimating the pool being around 28000 gallons + spa with overflow waterfall, and a pretty high water flow slide (Xstream brand - maybe up to 35 gpm) other components: Aquarite SWG Pentair 420 cartridge filter Heat pump Also - I meant to specify uprated to 2.2 SFHP (2HP w/ 1.1SF)

I'm not willing to make the investment for variable speed, but we are considering the two-speed whisperflow as well.

My pump is on the way out, so now to decide how to replace it. It is/was a 2hp uprated Whisperflo, running on 230V. I'm looking at basically an in-kind replacement, but noticed the energy efficient motor versions as an option. Both follow the same pump curve, but the energy efficient version...