Search results

They don't have to line up exactly. Electricians use electrical gutters or raceways connecting panels and devices all the time. Can't tell how much room you have to work with height-wise from your pic but you could trace out the old holes on the bottom of the existing panel and sit a small...

This is probably an old Hayward light receptacle as the skimmers are Hayward SP1070, there's only one screw mount in the light receptacle I have it on a switch with a dimmer but that can be changed, it's also connected to a relay in my intellicenter. Both this spa and the pool light are...

I added 1 gallon of Clorox from the laundry room on 7/8/22 - almost put in another half gallon I had but that one was low splash. 7/12/2022 test: CL: >5 PH: > 8.2 (7.89 - 7.97 per digital meter) - supposed to add 42oz Muriatic Acid per Pool Math FC: 3-3.5 per drop test - Pool math says...

I set it on Spa Hi & Blower and when I went outside I could see my pool suction vac running, so the spa mode wasn't tied into this (just the blower & pool pump). I ran over to the control panel but didn't see how to make sure it was in Spa mode each time that feature circuit was selected. Can...

Pentair IntelliTouch/EasyTouch to Next Gen Upgrade Kit - i10PS 522048 | PoolSupply4Less Says out of stock now. There are 6 versions, PS4L wasn't the cheapest, but they had it. Non-Legacy: 522047: Pool Only 522048: Pool Spa Combo 523049: Dual System earlier than 2012 is legacy...

I bought the EasyTouch 4SC-IC40 Pool Spa Combo 520543 and the IntelliTouch/EasyTouch to Intellicenter Upgrade - i10PS | 522048 These were delivered a day apart, the unused easytouch control panel, power supply, & fuses were replaced with the Intellicenter. I received the Intellicenter upgrade...

I just read the first page of this thread so far, I'll read more https://en.wikipedia.org/wiki/Ground_loop_(electricity)

Got it - thanks! I set up one called "Spa Hi & Blower" and set it on a 1h30m egg timer. I'll have to experiment with valves next. I have all kinds of ideas, next thing I'll do is light a walkway from the spa to a gate when this Feature circuit is active, I also plan on using the controller...

I've had my intellicenter up and running for ~6 days now and coming from fully manual control this has been a game changer, especially the valve controllers! I have a 3 programs going: 5am-8am: Spa 8am-5pm: Pool 5pm-11pm: Spa What I'd like to do is have a quick way to increase the pump...

Pretty sure the sticker says "3 wire control only" on both the new and old versions of the heater.

You want to check your pump addresses, you'll have to do that at both the pump(s) and the intellicenter. I'd probably start at the intellicenter. Settings -> Advanced -> Install -> Pumps. Looks like one of your pumps is working or is at least recognized by the intellicenter (the one that says...

Check your pump address at the pump controller if that's active, then go into your "pumps" settings and check that it's at the right address. My pump is a VST, it doesn't show connected if I have pump type set to VS, it has to be set to VSF. In the pumps settings the third/bottom option iirc...

my Mastertemp 400 is about 10 years old but may still be relevant to yours. I just installed a Intellicenter controller. My Mastertemp 400 doesn't have the RS485 port so I connected the Fireman switch to the 2-wire gas heater plug on the intellicenter. Inside the electrical box on p34, I...

I just switched to SWG from 3" pool tabs, last time I drained the pool was >5 years, could be as long as 10 years ago, so I wanted to start fresh. I got the TF-PRO Salt test but didn't see how to test salt with it - I just ran through the tests on the laminated half page so far. Salt levels...

I've had this pool/spa for 18 years and have looked at getting a chlorine generator a few times. I finally did it, and I'm almost done with the install: Intellicenter with IC40 and 2 valve controllers. I'm not sure the last time I drained my pool but it's been well over 5 years, so it's...