Search results

A gentle Magic Eraser might also work. Test it in a spot and check it does not remove any printing from the liner. https://www.troublefreepool.com/wiki/index.php?title=Magic_Eraser_on_Pools

Maybe @1poolman1 @Lake Placid @Poolbreh @QPSUtah @98Poolmaster has worked with those. https://www.pentair.com/content/dam/extranet/nam/pentair-pool/pool-manuals/rainbow/chlorinebromine-feeder-hc-3315-3330-3340-install-guide.pdf

The Laminar Installation Manual says to install a drain line at the bottom of the laminar. Do you know if that was done? Check if it is clogged...

@1poolman1 @Lake Placid any ideas about the gasket for a light niche in a vinyl liner?

There are pumps designed to move large volumes of water at low pressures and low volumes of water at high pressures. Pool, cover, and submersible pumps are designed to move high flow at low pressure. A pressure washer is an example of a pump designed to move low volumes of water at high...

In general no. Show us what gunk is on the liner. What specific product did you have in mind?

Between 7.2 and 7.5. Any pH in the 7's is ok. Don't sweat it.

The green actuator is your suction actuator, and the red actuator is your return actuator. Post pictures of both actuators when in POOL mode and SPA mode. Four pictures. The blue actuator is your solar valve. Ignore the yellow doodling. It looks like that pipe is your spa return.

Post pictures of your spa jets. Are your spa jets designed to move?

You have a Pentair Globrite light in a fiberglass niche. The white plastic ring is the niche, and you should NOT try to remove it. You can remove the light installed in the niche. Review how the light niche and light are installed in the manual...

https://www.troublefreepool.com/wiki/index.php?title=Evaporation_of_Pool_Water

Maintain 3-5 ppm of FC using liquid chlorine until your SWG is generating.

What was "regular speed"? You do not need the skimmers running the entire day. I run my pool at 1400 RPM 24/7 and my pool cleaner runs with the skimmers at 2400 RPM for 2 hours from 7AM to 9AM. That gets the surface debris into the skimmers for the day and is sufficient. If you wanted you...

Gas valves should not be repaired. @swamprat69 can wade in.

The cell should be happy with 2800.

Your IC40 should have the CELL light GREEN and be generating with salt at 2800. Give it more time for the salt to dissolve and circulate in your pool. While Pentair recommends 3600 the cell works fine anywhere from 2800 and up. Lower salt levels are a bit better for the longevity of the...

There is no reason to run your pump that fast. You do not need high pump speed due to pipe length. You are missing your Speed Labels. Read Jandy Aqualink RS - Further Reading and @MSchutzer @PoolGate can help you with your setup.

The fix is to replace the crumbling coping when you replace the liner.

Have you connected the antenna and pump individually and seen if one of them works without the other connecting? Did you measure the DC voltage across the two outside pins on the antenna connection?

Gas valves often fail due to an incorrectly installed gas line and sediment trap. Show us your gas line into the heater. https://www.troublefreepool.com/wiki/index.php?title=Heater_Maintenance#Heater_Gas_Sediment_Trap

Hydraulic cement. Cracks like that happen due to pressure on the wall. If you do not fix the root cause, the wall will crack again. Depends on how much effort you want to put into doing a lasting fix versus patching it and hoping for the best.

I added your checklist with a few edits to Plaster Installation and Maintenance - Further Reading

Start with the end in mind. Decide what your desired end state is, and then buy the equipment that will get you there. The pool equipment manufacturers do not want to give you optionality. They want to keep you in their ecosystem. I like the Pentair ecosystem, Hayward is ok, don't go to Jandy...

Welcome to TFP. End of what run? Pressure wash what? The flowers? Why do you think a more powerful pump is needed? Point the pump hose output onto the garden soil. Connect some type of oscillating lawn sprinkler to the pump output and let it spray on your garden.

The cord should be replaced every time a Jandy cell is replaced. An old cord can lead to premature cell failure. Your cell is depleted. Four years in Austin in a 26,000-gallon pool is about what I would expect. Your gas tank is empty, and you need to refill it. SWG technology has not improved...