Recent content by kundderek

Am piece of the OCLT 7.5 hrs later has me at FC = 12.

Shut the swg off 30 minutes ago. Pump will run overnight at 1400rpm. Just did my nighttime test for OCLT. FC = 12. Will see where I’m at in 8 hours. Good night.

Thanks for the reply. I'm waiting to do a water replacement or more likely renewal in the off-season and managing the chemistry in the meantime with PoolMath. It's that decreasing FC over the past week that threw me for a loop but as you and others have pointed out...algae is the likely...

Thanks for the reply. Ya, on the am of July 4th I did panic for a bit but soon saw previous posts on TFP that suggested everything would be fine haha. I've been of the 1/10th mindset where I try to target my FC to be 1/10th of CYA. Still learning but having a good time while doing so...

Thanks for the reply. Just tested the FC after having added the liquid chlorine this am and at a comfortable 10.5. I'm going to run the SWG at 100% for 6 hours just to see if it gives the requisite 0.5ppm/hr increase of 3ppm. I've got a reminder set for 9p to check FC, shut down the SWG for...

Hello - as some of my recent posts here have noted, I have chosen to delve into learning about / making adjustments to my pool chemistry. Armed now for the past two weeks with my Taylor K2006 and a new Jandy Aquapure SWG, I've been feeling pretty good about my work. I still have a pool guy but...

Ya, mine does as well. Their latest (2022) had Hardness at 296 and TA at 208.

Ya, I was off earlier with the up to 400 reference from tap. BWP's own report from 2022 has their hardness at 296. I test anywhere from 300 to 350 using the Taylor Kit on a garden hose sample. I will offer that I don't know a thing about this aspect of chemistry but i wonder if the initial...

Definitely. For what it's worth, the acid bath I was referring to was for the salt cell ie bathing it in a bucket of diluted muriatic acid. I haven't done an acid bath on the pool since filling it in July 2017.

My water co (BWP) in their annual water quality report - last published for year 2022 - had Alkalinity at 208 and Hardness at 296. You're about spot on with your numbers - with BWP being slightly higher. My tests over the past couple of weeks using the Taylor K2006 kit had CH at between 300...

Thanks for the comments. Regarding the SWG, I'm having a new one installed this week. My currently Jandy PCL 1400 is 7+ years old and hits service codes at anything above a 20% setting. Until I replace / renew my water in the offseason I'm going to have to be vigilant about maintaining it...

I appreciate the vote of confidence! Agreed on the CYA and CH. I think my Salt is ok now? it's on the higher side of the acceptable range at 3400ppm but within serviceable limits for the SWG, I believe. Still though, I plan to do the water swap in the offseason and maintain the other levels...

You are correct, but I'm still training up on the pool chemistry aspect and don't want to drop him until I am comfortable with all of it. For the $125/mo that I'm paying him - which some have noted is pretty cheap for my area - I'm still sorting out whether it's 'worth it' to have him do...

Ya, I've been making sure I don't get below 7.0. Yesterday's add (only half gallon) seemed to have little impact. I was at 7.8 and 130 (again) this am. I added another diluted gallon and am aerating. Will check again tomorrow. I just tested the water that comes from our garden hose. We...

I’ve spent the past three days working on one aspect of pool chemistry - TA. I was somewhere between 160 to 180 Friday am with ph of 8 initially after my partial drain and refill. I’ve added 2 gallons of 14.5% muriatic acid diluted with pool water via a Home Depot bucket - 1 gallon friday am...